Máquina de bobinado de cintas PET

Name: Cómo envolver bobinas en una máquina para embalar con cinta PET
Uploaded: 2018-07-04T06:39:40+00:00
Duration: 1 min 46 s
Description: > **Executive summary** > > PET strapping belt is sold in wound coils, and the coil edges are the part that gets damaged first: a dented edge makes the strap jam in the customer's strapping tool. Our coil wrapping machine passes stretch film through the coil eye and round the…

Resumen ejecutivo

PET strapping belt is sold in wound coils, and the coil edges are the part that gets damaged first: a dented edge makes the strap jam in the customer’s strapping tool. Our coil wrapping machine passes stretch film through the coil eye and round the outside, so both edges and the face are covered in one closed wrap.

The operator sets a green PET belt coil on the drive rollers of the green and yellow frame. A press arm closes onto the coil, the wrapping ring starts. White film is laid through the eye and over the outer face while the rollers turn the coil slowly, until the whole coil is closed in film.

Why PET belt coils are wrapped

A PET belt coil is a stack of thin strap layers held only by its own tension. If an edge hits the floor the outer layers fold, and a folded layer feeds badly in a strapping head. Film through the eye holds the layers together, keeps dust off the strap surface and stops the coil from telescoping when it is stood on edge. The wrapped coil can then go into a carton or onto a pallet without extra edge boards.

Secuencia de envoltura

The coil is placed flat on the drive rollers, eye over the ring opening.
The press arm comes down and holds the coil against the rollers.
The ring turns and carries the film roll through the eye and round the outer face.
The drive rollers turn the coil so each wrap overlaps the last one.
After one full turn of the coil the film is cut and the tail pressed down.
The press arm lifts and the wrapped coil is taken off.

datos de máquina

For PET belt coils the FPCA-300 range is the usual fit:

Parámetro	FPCA-300
DIÁMETRO INTERIOR DE LA BOBINA	250 – 510 mm
bobina de OD	400 – 900 mm
Ancho de la bobina	60 – 300 mm
Peso de la bobina	20-200 kg
Velocidad del anillo	10 90–XNUMX XNUMX r/min
Hora de terminar	20–38 s por bobina
superposición	10-90%
Potencia	2.4 kW
Film	LLDPE, PVC, PE or paper

Smaller coils run on the FPCA-200 (ID 150–400 mm, OD 250–500 mm). Core size outside these ranges is confirmed at quote.

Wrap time and film use

Wraps per coil ≈ π × OD ÷ (film width × (1 − overlap))

Wrap time ≈ wraps ÷ ring speed

Film per wrap ≈ 2 × (coil width + (OD − ID) ÷ 2)

Example only: a coil of OD 600 mm, ID 400 mm and width 150 mm, with 100 mm film at 50% overlap, advances 50 mm per wrap. π × 600 ≈ 1,885 mm, so 1,885 ÷ 50 ≈ 38 wraps. At 90 r/min that is about 25 s. Each wrap uses 2 × (150 + 100) = 500 mm of film, so about 38 × 0.5 = 19 m per coil.

Elección de cine

Stretch film is the usual choice: it clings to itself, needs no heat and leaves the strap clean. PVC gives a stiffer, clearer wrap for retail display. Paper or a paper-film mix is used where the customer wants to avoid plastic on the outside. A higher overlap gives more edge protection but uses more film and time, so it is set per coil.

Lista de verificación de selección

Diámetro interior, diámetro exterior y ancho de la bobina.
Peso de la bobina.
Bobinas por hora.
Tipo y ancho de la película.
Manual loading or conveyor in-feed and out-feed.
Label or logo tape needed on the wrap.

Seguridad

We design to EN ISO 12100:2010 for risk assessment, EN 415-10 for packaging machine safety and EN 60204-1 for the electrical equipment. The ring has a guard and the cycle starts only with the press arm closed; an emergency stop is within reach of the loading position.

Preguntas frecuentes sobre ingeniería

Q: Why wrap through the eye and not only round the outside? A: Only a through-the-eye wrap covers both edges, which is where PET belt coils get damaged.

Q: How long does one coil take? A: 20–38 s on the FPCA-300, depending on coil size and overlap.

Q: Can the machine take different core sizes? A: Yes, within the ID range above; the rollers and press arm are set for each size.

Q: Can loading be automated? A: Yes. In-feed and out-feed conveyors or a coil tilter are added to the layout, confirmed at quote.

El próximo paso

Send your coil ID, OD, width, weight and coils per hour a info@fhopepack.com.
Emparejamos the wrapper model, film and loading layout.
Respondemos dentro de las 24 horas. con una propuesta y un presupuesto.