Spoles pacēlājs ar bīdāmo galdu: pagriešana un atgriešanās par 90°

Kopsavilkums A coil tilter with a sliding table turns a coil or packed load 90° and lets the table travel out for loading by crane or fork-lift. In this clip our C-shaped tilter turns a film-wrapped load from upright to on its side between about 16 s and 40 s, then swings it back by about 56 s. Our mechanical upender with sliding table is rated for 5 T, single-way 90° turn-over, about L3000 × W2200 × H2600 mm, configured per project.

Saturs

Kas redzams klipā, secībā

The clip shows one machine from one camera position: a yellow C-shaped frame, open on one side, standing on a heavy blue base. A film-wrapped load sits inside the C. Each end of the frame has a round lifting lug.

  1. 0 to 12 s. The load rests upright on the table and nothing moves.
  2. Apmēram 16 sekundes. The frame starts to turn about its lower pivot and the load leans with it.
  3. Apmēram 20 līdz 32 sekundes. The turn continues until the load lies on its side, held between the two arms of the C.
  4. Apmēram 36 līdz 40 sekundes. The frame reaches the end of its turn, with the opening of the C facing up.
  5. Apmēram 44 līdz 56 sekundes. The frame swings back and the load returns close to its upright starting attitude.

The table stays in its turning position throughout this sequence; table travel belongs to loading and unloading, before and after the turn.

What a sliding-table coil tilter does

A coil tilter turns a load through 90° between lying on its face and standing on its side. The sliding table adds one more function: the table on the base runs on rails, so it can travel out from under the frame for loading and unloading and travel back for the turn. That keeps the crane hook or the fork-lift away from the frame while the load is placed.

The C-shaped frame holds the load on two faces, the table and the back of the C. The load turns with the frame instead of sliding across it, which protects edges and film wrapping.

Tilter element Sized by
C-frame opening Load height and width
Sliding table and rails Load footprint and loading method
Pivot and drive Load moment at 5 T
Pacelšanas cilpas Moving and installing the frame

Turn and return cycle time on the clip

Uzkāpiet uz klipša Laika logs ilgums
At rest before the turn 0 līdz aptuveni 12 s apmēram 12 s
Turn from upright to on its side apmēram 16 līdz 40 sekundes apmēram 24 s
Return toward upright apmēram 44 līdz 56 sekundes apmēram 12 s

The turn on the clip is slower than the return, which is usual: the drive slows the load into its side position, while the return carries less risk. Our page model is specified for a single-way 90° turn-over, where the frame turns the load once and the load leaves in its new attitude. The clip shows the frame returning, which is the two-way pattern. We choose one-way or two-way at the layout stage, because it changes the cycle.

Specifications of our sliding-table upender

Augšējais un noliekts ar bīdāmo galdu specifikācija
Maks. slodze 5 T
Apgrozījums 90°, vienvirziena
Machine izmērs about L3000 × W2200 × H2600 mm
Mašīnas svars about 4 T
Power spriegums Maiņstrāva 380 V, 60 Hz

Taktisks čeks

For an illustrative target of 30 loads per hour, one load must leave every 120 s, from 3,600 ÷ 30. On the clip the turn takes about 24 s and the return about 12 s, about 36 s of motion. That leaves about 84 s for sliding the table out, unloading, loading, sliding it back and letting the load settle. When the table travel and the crane or fork-lift move fit in that window, one tilter covers the target.

Selection checklist for a coil tilter with sliding table

  • Load OD, width or footprint, and weight up to 5 T.
  • Arriving attitude and the attitude the next station needs.
  • One-way turn-over, or turn and return.
  • Loading method: crane, fork-lift or conveyor, and the table travel needed.
  • Floor space for about L3000 × W2200 × H2600 mm, plus the table travel, which we fix at the layout stage.
  • Takt, including table travel and loading.

Vadības ierīces un drošība

The swing of the C-frame and the travel of the sliding table are the danger zones. Keep everyone outside both while the tilter runs, and load only with the table in its loading position and the frame at rest. Stop, isolate and lock out the tilter before anyone works on the load, the table or the rails, and never leave a load turned with the drive isolated unless it is mechanically supported.

The standards that apply depend on the destination market. For CE markets, EN 415-10 covers general requirements for packaging machines and ISO 12100 sets the risk-assessment method, which fixes guarding and the emergency-stop arrangement.

Inženierijas bieži uzdotie jautājumi

Q: Why add a sliding table to a coil tilter? A: The table travels out from under the frame on rails, so the crane or fork-lift places the load clear of the C-frame. The table then travels back and the frame turns the load 90°.

Q: What load does the sliding-table upender take? A: Our page model is rated for 5 T, with a single-way 90° turn-over and a machine size of about L3000 × W2200 × H2600 mm.

Q: How long does the turn take? A: On the clip the turn takes about 24 s and the return about 12 s. Add table travel and loading time before comparing with your takt.

Nākamais solis

We size a sliding-table coil tilter in three steps:

  1. Iesniedziet savu izkārtojuma zīmējumu with the load size, weight, turn angle, loading method and takt, to info@fhopepack.com.
  2. Saņemiet piedāvājumu 48 stundu laikā, including the frame and table arrangement and the cycle check against your takt.
  3. Rezervējiet objekta apsekojumu so we confirm the foundation, the table travel and the clearance around the frame.

Avoti

Pēdējoreiz pārskatīts: 2026-10-05

Jums arī varētu patikt

Rezervējiet zvanu
Rezervējiet zvanu