Samenvatting
A steel coil needs a clean, dry cover that holds the outer layer, and the cover material can be paper, film or both. This steel coil paper and film wrapping machine holds the coil on a rotating base with support rollers, and an overhead arm lays the wrap around the coil surface as it turns. Both wrap materials feed from the head, so the cover is chosen for the coil. Coil size, cover material and cycle settings are confirmed per project.
Inhoudsopgave
- Why paper or film on a coil
- Wat de machine doet
- Rotating base and overhead arm
- Paper, film or both
- Wat de beelden laten zien
- Typische configuratie
- Selectie checklist
- Bediening en veiligheid
- Veelgestelde vragen over techniek
- Volgende stap
- Gerelateerd lezen
- Bronnen en standaarden
Why paper or film on a coil
A steel coil has a surface that can mark and must stay dry. A paper cover cushions the surface, while a film cover seals out moisture; the right choice depends on the coil and how it travels.
Wrapping the coil with the machine gives a full cover that hand wrapping cannot match. Cover choice and coil range are confirmed per project.
Wat de machine doet
The machine is a steel coil paper and film wrapping machine. A coil is placed on the rotating base, which turns the coil while an overhead arm holds the wrap head. The head feeds the cover material around the outside of the coil in layers until the cover is set.
The operator places the coil and starts the cycle; the machine wraps and finishes. Coil diameter and wrap width are confirmed per project.
Rotating base and overhead arm
Support rollers on the rotating base hold the coil as it turns, and the overhead arm carries the wrap head above the coil. As the base rotates, the head lays the material across the coil surface.
Turning the coil instead of the head lets a simple head cover the full outer layer. Base speed and arm position are confirmed per project.
Paper, film or both
The wrap head holds both paper and film rolls, so the cover can be paper only, film only, or a combination. The footage shows the film covering the coil from the top as the coil turns.
Choosing the material in the cycle lets one machine cover different coils. Material setup is confirmed per project.
Wat de beelden laten zien
Our footage shows a coil placed on the rotating base, the overhead head applying cover while the coil turns, and the wrap finishing with the head lifting. It is a general demonstration, so your coil size, cover and cycle settings are confirmed with us per project.
Typische configuratie
De onderstaande cijfers geven de functionele ontwerpgrenzen weer in plaats van numerieke waarden en zijn per project bevestigd.
| Parameter | Typisch bereik, bevestigd per project. |
|---|---|
| Laden | steel coil on base |
| Draai | rotating base, support rollers |
| Wikkel | bovenhoofd |
| Materiaal | paper or film |
| Finish | head lift, end held |
| Elektrische voeding | 380 V driefase 50 Hz, of 220 V eenfase voor lichte machines, te kiezen per project. |
Selectie checklist
| Vraag | Bevestig per project |
|---|---|
| Laadbereik | spoeldiameter, breedte, gewicht |
| Hoes | paper, film or both |
| Cyclus | layers, band spacing |
| Finish | eindverwerking |
| Website | clearance for base and head |
| Elektrische voeding | spanning, fase en frequentie op locatie |
Bediening en veiligheid
Place the coil on the base and start the cycle from the control; the coil turns and the head wraps under power, then the wrap finishes and resets. Keep clear of the base and the head while the machine runs, with guarding around the working area.
Routine checks cover the base drive, the support rollers, the wrap head and the material feed, per the machine manual. Confirm the cover setup before each run.
Veelgestelde vragen over techniek
Q: What does this machine do? A: It wraps a steel coil with paper or film on a rotating base.
Q: Why rotate the coil? A: Turning the coil lets one head cover the full outer layer.
Q: Can it use both materials? A: Yes. Paper suits scuff protection where the coil surface must not mark, film suits moisture and dust sealing, and a paper inner cover with an outer film is the common export transit pack.
Q: How does the wrap finish? A: The head lifts and the end is held at the end of the cycle.
Q: What does it suit? A: Steel coils and similar cylindrical loads needing a clean, dry, scuff-protected cover.
Volgende stap
- Email us at info@fhopepack.com with your coil size and cover choice.
- We send a paper and film wrapping proposal and a layout drawing within 48 hours.
- We arrange a site survey to confirm material and cycle settings.
Gerelateerd lezen
- Papier- en foliewikkelmachine met stalen spoel
- Automatische spoelwikkelmachine
- Verpakkingsmachine met stalen spoel
- FHOPE verpakkingsmachine productlijnen
Bronnen en standaarden
- ISO 12100:2010 Veiligheid van machines, algemene principes voor ontwerp en risicobeoordeling
- EN 415-10:2014 Veiligheid van verpakkingsmachines, algemene eisen
- EN ISO 13849-1:2023 Veiligheid van machines, veiligheidsgerelateerde onderdelen van besturingssystemen
FHOPE steel coil paper and film wrapping machine demonstration video. Reviewed as a general demonstration; coil size, cover and cycle settings confirmed per project.
Laatst beoordeeld: 11-10-2026
