XNUMXつのクランプラーを備えたパレットティッパー|パレットチェンジャー

The working cycle follows five steps. Depending on the configuration, the machine is operated manually or via PLC control (representative specification, confirmed per project):

1. Push in with a pallet jack. The operator rolls the loaded pallet onto the floor-flush platform with a hand pallet truck — no forklift needed. Because the loading surface sits at ground level, the pallet jack enters directly.
2. 荷物を固定する。 The machine grips the load. Clamping pressure is set according to the goods; fragile or sensitive loads should be flagged during inquiry so suitable handling can be discussed.
3. Rotate 180°. The machine rotates the clamped load a full 180°, so the pallet is now on top and the load's underside is exposed.
4. Swap the pallet (when applicable). With the original pallet accessible, the operator removes it and places a replacement pallet on the exposed load face — or transfers the goods to a different pallet type.
5. Rotate back and push out. The machine returns to the starting position, the load rests on the new pallet, and the operator pulls it out with the pallet jack.

See the C-type operation in action: Watch the ground-level 180° pallet turnover video.

The figures below are the representative specifications stated on this page. Final configuration is confirmed per project.

• 回転： 180° full inversion
• 最大負荷： 1,500 kg (representative; confirmed per project)
• Pallet / load height: Up to 2,000 mm (representative; confirmed per project)
• 操作： Manual or PLC control (selected per project)
• 電源： 380 V / 50 Hz / 3 phase (confirm against your site supply)
• メインモーター： 5.5 kW (representative; confirmed per project)
• 読み込んでいます： Pallet jack (hand pallet truck) at floor level; no forklift required

Representative ratings apply to stable, unitized loads. Loose or non-rigid items may require side-support options confirmed per project. If your site power supply differs from 380 V / 50 Hz / 3 phase, state it in your inquiry so the electrical configuration can be reviewed.

• Load and height are representative. The 1,500 kg and 2,000 mm figures are page-stated representative values; the final rating for your machine is confirmed per project against your actual load.
• The load must be physically stable and unitized. Representative ratings assume stable, contained loads; loose or non-rigid items may need side support, confirmed per project.
• Pallet jack access and floor condition. Confirm the aisle width for pallet jack entry and the flatness of the floor at the installation position, per project.
• Pallet bottom construction matters. Full, closed double-face pallets block pallet-jack entry more than open (stringer/partial) pallets; state your pallet bottom type and pallet-jack fork width when you inquire.
• Special operating conditions. Cooling, cleanroom, and anti-static requirements are evaluated per project; discuss your environment explicitly in the inquiry.
• Inversion tolerance. If your goods cannot be fully inverted, this is the wrong machine family — see the 95°, V-shape, and pushing-type alternatives. If neither full inversion nor tilting is acceptable, contact us to discuss your handling method before ordering.

• Load the pallet properly. Stable, wrapped, or contained loads invert more predictably; flag loose or unstable stacks before ordering.
• Keep the rotation area clear. The machine sweeps a full 180° arc; operators and pallet jacks should stay outside the rotation zone during the cycle.
• Floor-level loading still requires a trained operator to position the load correctly on the platform before clamping.
• Use the control mode consistently. Whether configured for manual or PLC operation, follow the mode's defined sequence and do not intervene with the clamp or rotation while a cycle is running.

1. Goods dimensions: L × W × H, with and without the pallet.
2. Gross weight including the pallet.
3. 読み込み方法： pallet jack or forklift, available aisle width, and the pallet bottom construction (full closed double-face or open stringer/partial) with your pallet-jack fork width.
4. Photos of the loaded pallet.
5. Special restrictions: whether the load can be inverted, tilted, or clamped; fragile goods; frozen, cleanroom, or anti-static requirements.
6. サイト電源供給： voltage / frequency, and floor condition.

Can I use this machine without a forklift?
Yes — that is its core design. The lower clamp or platform lowers to floor level, so a hand pallet truck (pallet jack) can push the load in and pull it out. No forklift is required.

Is this a full 180° inversion? How is it different from a 95° or V-shape machine?
Yes, this machine rotates the load a full 180°, so the pallet ends up on top. A 95° pallet exchanger, V-shape pallet changer, or pushing-type changer only tilts, clamps, or transfers the load without turning it upside down. Choose 180° only if your goods tolerate full inversion.

What load and pallet height can it handle?
The page-stated representative values are up to 1,500 kg load and pallet/load heights up to 2,000 mm. Your actual configuration is confirmed per project.

What is the difference between manual and PLC control?
Both are available configurations. Manual operation suits lower-frequency use with an operator running each step; PLC control automates the sequence. The right choice depends on your cycle needs and staffing — confirm per project.

Does the floor need a pit or loading ramp?
No. The lower clamp or platform lowers flush to the floor, so a standard pallet jack loads and unloads directly from ground level — no dock, pit, or loading ramp is required for this step. Confirm the match to floor-surface flatness at your site.

保証とは何ですか？
The standard warranty is 1 year; an extended 2-year warranty applies only to selected models during special promotional periods. Confirm the warranty terms for your specific machine at quotation.