V字型パレットチェンジャーメーカー| FHOPE

1. Push in: The operator drives a hand pallet truck carrying the loaded pallet into the machine at floor level and positions it in the V-shaped clamping area.
2. Clamp and press: The V-shaped arms close on both sides of the load, and the scissor-lift mechanism presses down to hold the load securely between the arms.
3. Tilt 90°: The assembly tilts the clamped load 90° to the side. The load-interrupt function is active during tilting and lowering, so the motion can be halted if needed.
4. Exchange the pallet: With the load held on edge, the operator removes the bottom pallet, places the replacement pallet, and positions it under the load.
5. Return and push out: The machine tilts back to vertical, releases the clamp, and the operator pushes the re-palletized load out with the pallet truck.

See this sequence in action: Watch the hydraulic 90° tilt operation video.

The operator works from a position outside the tilt and sweep zone; the machine is designed so the operator is separated from the moving load during the cycle.

Representative configuration. Final load capacity, pallet footprint, and clamping pressure are confirmed per project.

• 傾斜角： 90° side tilt (not 180° inversion)
• Holding structure: V-shaped dual clamping arms with scissor-lift press-down
• Load-interrupt: Active during tilting and lowering strokes
• 読み込んでいます： Ground-level via hand pallet truck; no forklift required
• Total load height range (pallet + goods): 600–2000 mm (representative; confirm per project)
• 電気： Hydraulic power unit, approx. 2.2 kW, 380 V / 50 Hz (from unit nameplate; representative; confirm per project)
• Load capacity and pallet footprint: Confirmed per project according to load mass and packaging rigidity

• Side-rest stability required: Because the unit tilts 90°, cargo must withstand lateral contact pressure during the tilt without internal layer slipping. Confirm packaging rigidity and load pattern per project.
• Total load height range: 600–2000 mm (pallet + goods), representative; loads outside this range need project review.
• Load and footprint are per project: This page does not publish rated load capacity or pallet sizes; send your actual load mass and dimensions for confirmation.
• Forklift-free is conditional: Ground-level hand-pallet-truck loading works when the aisle lets a loaded pallet truck enter; confirm floor flatness and approach space.
• 90° tilt, not full inversion: Do not use it for loads that must be turned upside down; that belongs to a 180° inverter.
• Clamping pressure is calibrated per project: Fragile packaging must tolerate the specified clamp force without damage.
• サイクルタイム： Not published for this machine; it is dominated by the manual pallet swap and is confirmed per project.

• The load-interrupt function halts tilting or lowering immediately when activated.
• Controls keep the operator stationed outside the physical tilt and sweep zone during the cycle.
• The machine is operated from a defined operator position; keep the approach zone clear while the load is tilted.
• Ground-level loading avoids lifting a load overhead; use only the specified hand pallet truck for infeed and outfeed.

1. 積載寸法： length × width × height, with and without the pallet.
2. Gross weight with the pallet.
3. 読み込み方法： hand pallet truck / forklift, and approach aisle width.
4. A photo of the loaded pallet.
5. Special constraints: whether the goods can be tilted, clamped, or pushed, fragile or cold-storage or cleanroom or ESD requirements.
6. Site power: voltage / frequency, and floor conditions.

Can this unit flip a pallet fully 180°?
No. It tilts the clamped load 90° to the side so the bottom pallet can be exchanged. If you need a full 180° inversion, use a 180° pallet inverter.

Do I need a forklift for this machine?
No. Loading is by hand pallet truck at floor level. Confirm your aisle width and floor flatness for the loaded pallet truck.

Will clamping damage fragile goods?
Clamping pressure is calibrated per project against your actual load. Goods must be in stable, closed packaging and must not shift or slide during the 90° tilt.

What load capacity does it handle?
This page does not publish a rated capacity. Confirm your load mass and pallet footprint with us, and the configuration will be sized per project.

What pallet height range does it accept?
Total load height (pallet + goods) 600–2000 mm, representative; outside this range requires project review.

保証とは何ですか？
The standard warranty is 1 year; an extended 2-year warranty applies only to selected models during promotional periods. Confirm the applicable terms for your order.