Kokkuvõte
Hose winding and strapping are the two steps that turn a running length into a sellable coil, and doing them apart leaves a gap for the coil to loosen. This pipe coiling and strapping machine combines hose winding with strapping, closing each coil in the same flow. We build combined winding and strapping machines. Hose range and coil plan are confirmed per project.
Sisukord
- Why the two steps share a machine
- Mida masin teeb
- Winding the hose
- Strapping after winding
- The combined flow
- A closed coil at the end
- Tüüpilised konfiguratsiooni
- Mida videos näidatakse
- Valiku kontroll-leht
- Töötamine ja ohutus
- Inseneri KKK
- Järgmine samm
- Seotud lugemine
- Allikad ja standardid
Why the two steps share a machine
A wound hose that sits unwrapped is a hose that can spring open before it is strapped. Each extra handling between winding and strapping is a chance for the coil to move. Combining the steps on one machine is what closes that gap. The hose range and its spring are confirmed per project.
Mida masin teeb
The machine winds the hose into a coil and straps the coil in one flow, combining winding and strapping on a single machine. Winding lays the coil, and strapping closes it before the coil leaves the station. Because the steps are combined, the coil is always closed in the shape it was wound. The covered cycle is confirmed per project.
Winding the hose
The hose is wound in even turns with the machine controlling the lay, so each ring sits on the last without gaps. Controlled winding keeps the coil stable enough to take a strap the moment it finishes. The lay and the coil follow the hose, confirmed per project.
Strapping after winding
The strap is applied as the wind completes, at the same station, holding the coil before it can spring. Strapping after winding, without moving the coil, is what keeps the coil in its wound shape. The strap positions and tension follow the coil, confirmed per project.
The combined flow
The machine replaces a separate winder and a separate strapper with one combined flow: hose in, coil closed, out. Combined flow cuts the handling between steps and the floor they used to need. The design also keeps the coil stable through the whole step. The flow layout is confirmed per project.
A closed coil at the end
What leaves the machine is a closed coil, wound and strapped in one pass, ready for the pallet or the next station. A closed coil holds its shape through handling and transport. The machine delivers the coil closed at the standard the hose needs. The coil standard is confirmed per project.
Tüüpilised konfiguratsiooni
Allolevad joonised loetlevad funktsionaalse disaini piirid, mitte numbrilised väärtused, ja need kinnitatakse iga projekti kohta eraldi.
| Parameeter | Tüüpiline vahemik, kinnitatud projekti kohta |
|---|---|
| voolik | winding range |
| pool | läbimõõdu komplekt |
| Rihmad | positsioonid, pinge |
| Sammud | kombineeritud |
| Kontroll | PLC |
| Elektrivarustus | 380 V kolmefaasiline 50 Hz või 220 V ühefaasiline kergmasinate jaoks, valitud projekti järgi |
Mida videos näidatakse
Our footage shows a pipe coiling and strapping machine combining hose winding and strapping. It is a general demonstration, so your hose range and coil plan are confirmed with us per project.
Valiku kontroll-leht
| Küsimus | Kinnitage projekti kohta |
|---|---|
| voolik | läbimõõdud |
| pool | läbimõõdu komplekt |
| Rihmad | arv, pinge |
| Sammud | kombineeritud |
| Kontroll | PLC |
| Elektrivarustus | pinge, faas ja sagedus kohapeal |
Töötamine ja ohutus
Run the cycle from the panel and the machine winds and straps each hose automatically. Keep clear of the winding head, hose path, strap unit and outfeed while the machine runs, with guarding and emergency stops at the operator position. Routine checks cover the winding drive, guides, strap head, sensors and control, per the machine manual. Confirm the coil settings against the hose before each run so coils leave closed.
Inseneri KKK
Q: Why combine winding and strapping? A: A hose that sits wound but unstrapped can spring open before it is closed.
Q: How does winding run? A: The machine lays each turn evenly, giving a stable coil that takes the strap at once.
Q: When is the strap applied? A: As the wind finishes, at the same station, before the coil can move.
Q: What does the combined flow replace? A: A separate winder and a separate strapper, and the handling between them.
Q: What leaves the machine? A: A closed coil, wound and strapped in one pass, ready for the pallet.
Järgmine samm
- Saatke meile oma voolikute valik ja torustiku kiirus e-posti teel aadressile info@fhopepack.com.
- Saadame teile 48 tunni jooksul kerimis- ja sidumispakkumise ning küljendusjoonise.
- We arrange a site survey to confirm hose range and combined flow.
Seotud lugemine
- Automaatne torurullija ja kinnitusmasin
- Automaatne torurulli ja vooliku kerimismasin
- Voolikupoolide mähkimismasin kilega
- FHOPE pakkimismasinate tootesarjad
Allikad ja standardid
- ISO 12100:2010 Masinate ohutus, projekteerimise ja riskihindamise üldpõhimõtted
- EN 415-10:2014 Pakkemasinate ohutus, üldised nõuded
- EN ISO 13849-1:2023 Masinate ohutus, juhtimissüsteemide ohutusega seotud osad
FHOPE pipe coiling and strapping machine demonstration video. Reviewed as a general demonstration; hose range confirmed per project.
Viimati üle vaadatud: 26.08.2026
