غلاف لفائف بسيط

ملخص تنفيذي

A simple coil wrapper is a one-station machine for plants that wrap cable, wire or hose coils by the hundred, not by the thousand. The operator loads the coil, presses start and takes it off wrapped. What decides the result is the setup: roller spacing, film tension and overlap. This article covers how our simple coil wrapper is set and run.

The wrapper has a white body with a blue arm and clamp. A coil sits on the rollers already closed in clear film, and a driven roller above it turns the coil while the film ring passes through the eye.

جدول المحتويات

الأجزاء الرئيسية

  • بكرات الدعم: carry the coil and turn it.
  • Top press roller: holds the coil down so it turns without slipping.
  • خاتم التغليف: carries the film roll through the coil eye.
  • عربة الفيلم: holds the roll and sets the film tension.
  • لوحة التحكم: start, stop, ring speed and coil speed.

Setting up for a new coil size

  1. Set the support rollers to the coil OD so the eye sits over the ring opening.
  2. Lower the top press roller onto the coil face.
  3. Fit a film roll of the right width and thread it through the carriage.
  4. Set the film tension so the film lies flat without tearing.
  5. Set ring speed and coil speed for the overlap you want.
  6. Wrap one test coil and check the overlap at the inner and outer edge.

Running a coil

  1. Place the coil on the rollers.
  2. ثبّت طرف الفيلم على الملف.
  3. Press start; the ring and rollers run together.
  4. After one full coil turn the machine stops.
  5. Cut the film, press the tail down and lift the coil off.

بيانات الجهاز

العناصر FPCA100 فبكا-200
لفائف معرف 90 – 250 مم 150 – 400 مم
لفائف OD 150 – 400 مم 250 – 500 مم
عرض لفائف 50 – 180 مم 80 – 200 مم
الوزن فائف 2-30 كجم 2-50 كجم
سرعة الرنين 10–120 دورة/دقيقة 10–120 دورة/دقيقة
وقت الانتهاء 18-30 ثانية 20-30 ثانية
تداخل 20–90 ٪ 20–80 ٪
الطاقة 1.8 كيلو واط 2.0 كيلو واط

Overlap and speed settings

The overlap is set by the ratio of ring speed to coil speed. The film advances round the outer edge by:

Advance per wrap ≈ film width × (1 − overlap)

Coil turns needed ≈ π × OD ÷ advance

Example only: 60 mm film at 50% overlap advances 30 mm per wrap. A 300 mm OD coil has an outer edge of π × 300 ≈ 942 mm, so 942 ÷ 30 ≈ 31 wraps, or about 16 s at 120 r/min. The inner edge is shorter, so the film there overlaps more; check the overlap at the outer edge, where it is lowest.

The formula gives net wrapping time only. The full cycle adds loading, fixing the film end, the soft start and stop, cutting and unloading, so time a real coil at your site before setting the shift output.

الشيكات اليومية

  1. Rollers clean and free of film scraps.
  2. Film carriage tension even.
  3. Ring guard and emergency stop working.
  4. Air and power supply normal.
  5. Test coil overlap checked at shift start.
  6. Film stock for the shift.

قائمة التحقق من الاختيار

  1. القطر الداخلي والخارجي للملف وعرضه.
  2. وزن الملف.
  3. عدد اللفات لكل وردية.
  4. عرض الفيلم ونوعه.
  5. Manual loading or conveyor.
  6. Label on the wrap.

سلامة

We design to EN ISO 12100:2010 for risk assessment, EN 415-10 for packaging machine safety and EN 60204-1 for the electrical equipment. Keep hands clear of the ring while it runs, and load only with the machine stopped.

أسئلة وأجوبة هندسية

Q: Why is the overlap higher on the inside of the coil? A: The inner edge is shorter, so the same film covers it more times.

Q: How long does one coil take? A: 18–30 s on the FPCA100.

Q: Can it wrap with paper? A: Film is standard; other materials are confirmed at quote.

Q: Can it be upgraded later? A: Yes, conveyors or a coiler can be added in front, confirmed at quote.

الخطوة التالية

  1. Send your coil ID, OD, width and weight إلى info@fhopepack.com.
  2. نحن نطابق the wrapper model and film.
  3. نقوم بالرد خلال 24 ساعة مع تقديم عرض سعر واقتباس.

مصادر

  • FHOPE product pages: FPCA100, FPCA-200 cable coil wrapping machines
  • إن آيزو 12100:2010؛ إن 415-10؛ إن 60204-1

آخر مراجعة: 2026-10-20

منشورات ذات علاقة

احجز مكالمة
احجز مكالمة