Резюме This video shows a horizontal stretch wrapping machine wrapping a single long, square metal tube on a roller conveyor. The tube moves through an enclosed wrapping zone, receives a spiral layer of clear stretch film, and exits fully wrapped. The footage demonstrates the full feed–wrap–exit cycle in about 24 seconds of film, with visible safety guarding, an emergency stop, and a push-button control panel.
Long, narrow products such as steel tubes, bars, and profiles are awkward to wrap by hand. They are heavy to turn, hard to hold, and manual wrapping rarely produces a consistent film tension from end to end. The machine in this video addresses exactly that problem: it wraps a narrow workpiece automatically while the product travels horizontally through the machine on rollers.
Что показано на видео
The footage runs for roughly 24 seconds and follows one workpiece through the complete wrapping cycle:
| Дата | Что происходит |
|---|---|
| 0-е - 4-е | A dark brown square metal tube rests on the roller conveyor at the entrance of the wrapping zone. The machine frame and wire mesh safety guard are visible. |
| 4-е - 12-е | The tube moves forward on the rollers. Clear plastic film is fed from a roll and applied in a spiral pattern as the tube rotates and advances through the central wrapping section. |
| 12-е - 22-е | The tube, now fully encased in tight film, passes under a set of vertical rollers that guide and secure the film. The camera angle shifts to show the wrapped product moving toward the exit. |
| 22-е - 24-е | The wrapped tube exits the machine and continues along the conveyor out of frame. |
The cycle is continuous: feed, wrap, exit. There is no visible pause for manual adjustment, which is the core advantage of this layout for long products.
Заметки о непосредственных наблюдениях
The following points stay close to what is actually visible in the frames:
- Продукт представляет собой single, long, square-section metal tube, dark brown with a slightly rusted or oxidized surface — raw metal, not a finished painted part.
- Рама станка grey painted metal; film feed arms and side guides are ярко-желтый; conveyor rollers are silver-colored metal.
- The wrapping zone is enclosed by a grey wire mesh safety guard.
- The wrapping mechanism uses a film head that moves along the length of the product while the product rotates, applying film in a spiral pattern.
- A black control box with a small digital display and several push-button switches is mounted on the side of the frame, connected with blue and red pneumatic hoses and electrical wiring.
- A black circular emergency stop button is visible on the side of the machine frame.
- After wrapping, the tube is covered in a transparent, crinkled plastic film applied tightly around the full length.
- Text “2450” appears on background items (a paper bag and a box label); it is not machine-related.
Как работает машина
The layout is a straightforward inline conveyor system:
- Корм. The operator or an upstream process places the narrow product on the roller conveyor. It enters the machine’s working area from the front.
- Сворачивать. Inside the central wrapping zone, the product rotates while the film head travels along its length. Stretch film is drawn from a side-mounted roll, stretched, and wound in an overlapping spiral so the entire surface is covered.
- Secure and exit. Guide rollers help keep the film in place as the product passes through. The fully wrapped tube exits at the back and continues down the conveyor.
Because the product stays horizontal and supported on rollers throughout, the machine suits items that are too long or heavy to rotate safely by hand. The spiral overlap means film tension and coverage stay consistent along the whole length — something manual wrapping on long sections rarely achieves.
Чего не показано в видео
The footage demonstrates the process clearly, but several facts a buyer needs are simply not observable:
- Номинальная мощность — maximum product weight and size range
- Размеры Машины (length, width, height) and footprint
- Время цикла as a throughput figure
- Номер модели and available configurations
- Требования к питанию (voltage, phase)
- Технические характеристики held by the machine
- Film type, width, and gauge options
- Whether infeed/outfeed can be automated or linked to a production line
These are normal gaps for a short demonstration video. Treat anything not listed above as уточнить у производителя перед принятием решения о покупке.
Где находится эта машина
Based on what the footage shows, this type of horizontal wrapper is a good match when:
- You wrap long, narrow products — tubes, bars, rails, extrusions, profiles.
- Products arrive as отдельные детали that need dust, moisture, and scuff protection for transport or storage.
- Вы хотите, стабильное качество обертывания without an operator turning and holding the product.
- The product can pass through the machine on a роликовый конвейер in line with your material flow.
It is likely a poor fit when:
- Продукция irregularly shaped or very wide — the wrapper is designed for narrow, long sections.
- You need highly precise, orientation-specific film application that a vertical wrapper would handle better.
- Products cannot pass horizontally through a guarded wrapping zone.
Контрольный список проверки покупателя
Before requesting a quotation, confirm the following with the manufacturer:
- Minimum and maximum product length, cross-section, and weight the machine accepts
- Conveyor roller spacing and whether it suits your smallest product
- Compatible film types, widths, and pre-stretch levels
- Cycle time for a product like yours
- Power supply and compressed air requirements
- Safety guard interlock design and compliance with your facility’s standards
- Integration options for upstream/downstream conveyors
- Условия гарантии и наличие запасных частей
Часто задаваемые вопросы
What kind of products can this machine wrap? The video shows a long square metal tube, and the machine is designed for long, narrow industrial items such as tubes, bars, and profiles. Exact size limits — check with the manufacturer.
Does the operator need to turn the product during wrapping? No. In the footage the product rotates and advances on its own through the wrapping zone; the operator’s role is limited to feeding and monitoring.
Is the wrapping zone safe to work around? The wrapping mechanism is enclosed in a wire mesh safety guard, and an emergency stop button is mounted on the frame. The guard appears designed as an interlock so the machine cannot run while open — confirm interlock details with the manufacturer.
Can it handle products other than metal tubes? It is built for narrow, long items; irregular or very wide products may not be suitable. Provide your product samples or drawings to the manufacturer for confirmation.
How tight is the wrap? The film is stretched during application and appears tight and secure over the full tube length in the video. Actual film tension settings depend on product and film choice — discuss with the manufacturer.
Примечания по обслуживанию
Routine upkeep for a machine of this layout generally focuses on the moving parts visible in the video:
- Сохранить конвейерные ролики clean and turning freely; debris from rusty raw stock can build up.
- Диагностика film feed arms and guides (the yellow components) for wear and film residue.
- Проверка pneumatic hoses and fittings for leaks, as pneumatic lines are visible on the frame.
- Проверить аварийной остановки and guard interlock function at regular intervals.
- Confirm lubrication points and service intervals — проконсультируйтесь с производителем for the official maintenance schedule.
Источник и метод
This article is based on the machine demonstration video embedded above. The footage was analyzed frame-by-frame using a vision model on sampled stills; the video contains background music only, with no narration or speech, so no spoken content was transcribed. All process descriptions come directly from what is visible on screen. Specifications not visible in the video are not stated here and should be confirmed with the manufacturer.
Связанное чтение
- Обзор машины для стретч-пленки
- Машина для обертывания с вращающимся кольцом
- Автоматическая горизонтальная упаковочная машина
- Полуавтоматическая машина для упаковки паллет
- Автоматическая машина для упаковки поддонов
Следующий шаг
If you wrap long tubes, bars, or profiles and want consistent, hands-off film protection, the horizontal stretch wrapper shown above is worth evaluating against your product dimensions. Share your product size, weight, and daily volume through the контактная страница to get a configuration recommendation and quotation.
Опубликовано: 2026-09-03
