개요
A coil upender is built to work by tipping a coil between horizontal and vertical on a large tilting cradle, so the coil changes orientation without being lifted by hand. The cradle tips the coil automatically from horizontal to vertical, so the orientation change happens without overhead-crane or manual handling. Coil weight, coil dimensions and tilt angle are confirmed per project.
차례
- Why use a coil upender
- What the upender does
- Cradle and tilt mechanism
- Upending cycle and return
- 영상에 나타난 내용
- 일반적인 구성
- 선택 체크리스트
- 운영 및 안전
- 엔지니어링 FAQ
- 다음 단계
- 관련 독서
- 출처 및 표준
Why use a coil upender
A steel or wire coil needs to be turned between two orientations at different points in the line: flat for storage and upright for feeding or transport. Turning a heavy coil by hand is slow and unsafe.
A coil upender tips the coil in a controlled cradle, so orientation changes happen without manual lifting. Coil weight and coil dimensions are confirmed per project.
What the upender does
The upender is a floor-mounted machine with a blue base and a large yellow cradle on top. The cradle holds the coil and rotates around a horizontal axis to move the coil from flat to upright, or back again.
The machine tips the load smoothly, then returns to the starting position ready for the next coil. Tilt angle and cycle time are confirmed per project.
Cradle and tilt mechanism
The cradle is a large C-shaped or half-cylindrical frame with several parallel horizontal plates inside that support the coil during the move. The frame is connected to the base by a central shaft.
The cradle rotates around this shaft to raise the coil from horizontal to vertical. Cradle width and coil support plates are confirmed per project.
Upending cycle and return
The cycle begins with the cradle closed in the horizontal position. The cradle then rotates in one direction, reaches the upright position, and rotates back to horizontal to complete the demonstration pass.
For a loaded coil the same movement tips the coil to the required orientation, then the cradle returns empty or with the next coil. Tilt speed and holding position are confirmed per project.
영상에 나타난 내용
Our footage shows a floor-mounted coil upender completing an empty demonstration pass. The yellow cradle starts in the horizontal closed position, rotates to upright, and returns to horizontal while two workers stay clear of the machine. No coil is fed during the pass, so the dry run verifies the cradle travel and limit positions and checks the clearance around the machine before a loaded coil is handled. Coil weight, coil dimensions and tilt angle are confirmed with us per project.
일반적인 구성
아래 표는 수치 값이 아닌 기능적 설계 경계를 나열한 것이며, 프로젝트별로 확정된 내용입니다.
| 매개 변수 | 일반적인 범위이며, 프로젝트별로 확정됩니다. |
|---|---|
| 공작물 | steel or wire coil handled between orientations |
| 요람 | large C-shaped or half-cylindrical frame with support plates |
| Base | floor-mounted blue base with a central shaft |
| 드라이브 | cradle rotates around the horizontal shaft |
| 주기 | from horizontal to upright and back to horizontal |
| 조작 | workers keep clear while the cradle moves |
| Control: | machine control with cycle start and hold; panel per project |
| 전기 공급 | 380V 3상 50Hz 또는 경량 장비의 경우 220V 단상(프로젝트에 따라 선택) |
선택 체크리스트
| 문제 | 프로젝트별로 확인하세요. |
|---|---|
| 코일 범위 | weight, outer diameter, width and core size |
| 경사각 | required orientation change, typically 90 degrees |
| 요람 | C-shaped or half-cylindrical frame, selected per project by coil outer diameter and loading method (forklift or crane) |
| 주기 | tilt time and hold position for the line |
| 바닥 | machine footprint and surrounding clearance |
| 전기 공급 | 현장에서 전압, 위상 및 주파수 측정 |
운영 및 안전
Position the coil in the cradle, start the tilt cycle, and let the machine rotate the load to the required orientation. Stand clear of the cradle while it moves, and hold the coil stable as the cradle returns.
Routine checks cover the shaft drive, the cradle plates and the floor fixing, per the machine manual. Confirm the coil is seated in the cradle before each cycle.
엔지니어링 FAQ
Q: What does a coil upender do? A: It tips a coil between horizontal and vertical in a controlled cradle, without manual lifting.
Q: How does the tilting work? A: The cradle rotates around a horizontal shaft on the base, carrying the coil from one orientation to the other.
Q: Can it turn a loaded coil in real operation? A: The cradle is built to carry a coil through the pass; the exact coil weight and dimensions are confirmed when you send your coil details.
Q: Why is an upender safer than turning by hand? A: The load stays supported in the cradle during the whole move, keeping people away from the tipping point.
질문: 어떤 전원이 필요합니까? 답변: 이 기계는 기본적으로 380V 3상 50Hz로 작동하며, 소형 기계의 경우 프로젝트에 따라 220V 단상으로도 구성할 수 있습니다.
다음 단계
- Email us at info@fhopepack.com with your coil weight, outer diameter and width.
- We send a coil upender proposal within 48 hours.
- We confirm the tilt angle, cradle size and cycle time for your coil.
관련 독서
- 코일 업펜더는 어떻게 작동하나요? 초보자를 위한 종합 가이드
- 실제 작동 중인 대형 및 장형 코일 업엔더
- 코일 틸터 및 업엔더: 팔레트에 적재된 코일을 90도 회전시키는 장치
- FHOPE 포장 기계 제품 라인
출처 및 표준
- ISO 12100:2010 기계 안전, 설계 및 위험 평가에 대한 일반 원칙
- EN 415-10:2014 포장기계의 안전, 일반 요구사항
- EN ISO 13849-1:2023 기계의 안전, 제어 시스템의 안전 관련 부품
FHOPE coil upender demonstration video. Reviewed as a general demonstration; coil weight, coil dimensions and tilt angle confirmed per project.
최종 검토일: 2026년 10월 12일
