Ringkasan Eksekutif A semi-auto pallet stretch wrapper turns the load on a turntable while a film carriage climbs the column. The operator brings the pallet, ties on the film and starts the cycle, and the machine wraps to the photocell-set height. Our A100 and A200 take loads up to 1,500 × 1,500 × 1,800 mm on a 2,000 mm turntable. Below are the setup practices that give a stable load with the least film, and a worked example of film per load.
Daftar Isi
- The technology inside a semi-auto wrapper
- A100 and A200 specifications
- Seven setup practices for a stable load
- Worked example: turns, time and film per load
- Common wrapping faults and their causes
- Daftar periksa seleksi: apa yang perlu Anda kirimkan kepada kami
- Keselamatan dan EN 415-6
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- sumber
The technology inside a semi-auto wrapper
Three systems do the work. The meja putar turns the load on a ring gear bearing with soft start and stop, so the load does not jolt. The kereta film rides up and down the column. It pre-stretches the film between rollers before it reaches the load. The PLC runs the cycle, counting wraps and reading a photocell that finds the top of the load.
On our machines the panel and display sit on the carriage side of the column. The operator sets bottom, middle and top wrap counts, overlap and film force there. A re-wrap function adds wraps to a load that needs more without a full new cycle.
A100 and A200 specifications
| Barang | A100/A200 |
|---|---|
| Ukuran beban | max. 1,500 × 1,500 mm, min. 500 × 500 × 500 mm |
| Tinggi beban | Max. 1,800 mm |
| Beban berat | Max. 2,000 kg |
| Turntable | 2,000 mm diameter, 100 mm high, 10 mm plate, ring gear bearing |
| Kecepatan putar | 13 r/min, dapat disesuaikan |
| Keluaran | 20–40 muatan/jam |
| Film | LLDPE, 0.025 mm, 500 mm wide, 76 mm core, 15 kg roll |
| Pra-peregangan | 250%, opsional 100% hingga 300% |
| Penghitung bungkus | independent top, middle and bottom |
| Menyediakan | 220 V, 1 fase, 50 Hz |
| berat mesin | 650 kg, forklift pockets front and rear |
Both spec sheets list 250% pre-stretch. Only the A200 sheet lists a dedicated pre-stretch motor, so confirm the pre-stretch drive with us when you choose between them. Both machines have a red mushroom-head emergency stop and a lockable electrical disconnect.
Seven setup practices for a stable load
- Centre the load. An off-centre load swings wide and pulls film unevenly. Check that the load diagonal fits the turntable’s turning diameter.
- Tie the load to the pallet. Set enough bottom wraps for the film to reach down over the pallet deck. Most load shifts start between the pallet and the first layer of cartons.
- Lock the top. Top wraps hold the top layer, which has the least weight on it and moves first.
- Set overlap with carriage speed. Overlap depends on how far the carriage moves in one turntable turn, so carriage speed sets it.
- Match pre-stretch to the load. High pre-stretch saves film on firm, square loads. Lower it for soft bags or loads that crush.
- Use the photocell. Let the sensor find the load top instead of a fixed height, so short loads do not waste film above them.
- Store film well. Cold or dusty film tears at the pre-stretch rollers. Keep rolls indoors at room temperature.
Worked example: turns, time and film per load
Take a 1,200 × 1,000 × 1,500 mm load. These are illustrative customer figures.
Pengecekan kecocokan. The load diagonal is √(1,200² + 1,000²) = 1,562 mm, inside the 2,000 mm turntable.
Ternyata. For 50% overlap with 500 mm film, the carriage must rise 250 mm per turn. At 13 r/min that means a carriage speed of 250 × 13 = 3,250 mm/min. Our cycle runs both ways: the carriage spirals down the load and then climbs back up. Each 1,500 mm pass takes 1,500 ÷ 250 = 6 turns, so the two passes take 12. Add 3 bottom and 3 top wraps, illustrative settings, for 18 turns.
Waktu. Eighteen turns at 13 r/min take about 1.38 min, or 83 s of turning. Add the film tie-on, cut and forklift moves, and compare the total with your loads per hour.
Film. One turn wraps a perimeter of 2 × (1.2 + 1.0) = 4.4 m, so 18 turns put 79.2 m on the load. At 250% pre-stretch, 1 m off the roll becomes 3.5 m, so the roll gives 79.2 ÷ 3.5 = 22.6 m. LLDPE weighs about 920 kg/m³. That roll length weighs 0.000025 × 0.5 × 22.6 × 920 = 0.26 kg. A 15 kg roll covers about 58 loads like this. A single up pass would save a third of that film, at the cost of a weaker wrap.
Common wrapping faults and their causes
| Kesalahan | Penyebab umum |
|---|---|
| Film tears at corners | Film force too high, or sharp carton edges |
| Load leans after wrapping | Too few bottom wraps, film not reaching the pallet |
| Top layer slides | Too few top wraps |
| High film use | Overlap or wrap counts set higher than the load needs |
| Bungkus longgar | Pre-stretch too low or film force too low |
Daftar periksa seleksi: apa yang perlu Anda kirimkan kepada kami
- Pallet size and the largest load footprint.
- Load height range and heaviest load.
- Muatan per jam.
- Jenis muatan: karton, karung, drum, atau barang lepas.
- Whether you need powered pre-stretch.
- Pasokan listrik tersedia di lokasi.
Keselamatan dan EN 415-6
We design pallet wrappers to EN 415-6 and assess risks to ISO 12100. On a semi-auto machine the operator works close to the load, so the main hazards are the turning load and the carriage. Mark the floor round the turning circle and keep out of it while the turntable runs. We fit the carriage with protection against falling and against trapping a foot beneath it as it comes down. The emergency stop and lockable disconnect come as standard.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: What does 250% pre-stretch mean? A: Each metre of film is stretched to 3.5 m before it reaches the load.
Q: Can I wrap a load heavier than 2,000 kg? A: Not on the A100 or A200. We quote a heavier turntable for that.
Q: Why does overlap change when I change carriage speed? A: The carriage moves further in each turntable turn, so the film bands spread apart.
T: Standar keselamatan apa yang berlaku? J: ISO 12100 untuk penilaian risiko dan EN 415-6 untuk mesin pembungkus palet, di pasar CE.
Langkah selanjutnya
- Email your pallet sizes, load heights and loads per hour untuk info@fhopepack.com.
- Kami akan membalas dalam waktu 24 jam dengan sebuah proposal. naming the model and film settings.
- Kami mengirimkan gambar tata letak. with the forklift path round the machine.
Bacaan terkait
- Mesin pembungkus palet A100
- Mesin pembungkus palet A200
- Mesin pembungkus peregangan palet semiotomatis A100
- Robotic arm semi-automatic pallet wrapper
- Pallet wrapper with top sheet dispenser
sumber
- Specifications: FHOPE A100 and A200 pallet wrapping machine product pages
- Video mesin: semi-auto pallet stretch wrapper on YouTube
- Turns and film: our worked example, illustrative load figures; LLDPE density about 920 kg/m³
- Standar: EN 415-6 (mesin pembungkus palet); ISO 12100:2010
Terakhir ditinjau: 17-10-2026
