Vezetői összefoglaló
Coil upending and turning keeps a steel coil safe while it is changed from horizontal to vertical or back again. A lifting rig lowers the coil onto a curved support arm, and the machine tilts the arm to stand the coil up or lay it flat. The operator runs the movement from a control cabinet beside the machine, and the coil is handled again without being lifted by hand. Coil size, weight and cycle speed are confirmed per project.
Tartalomjegyzék
- Why upend and turn coils for material handling
- Mit csinál a gép
- Support arm and tilting motion
- Ciklus és vezérlés
- Amit a felvétel mutat
- Tipikus konfiguráció
- Kiválasztási ellenőrzőlista
- Működés és biztonság
- Mérnöki GYIK
- Következő lépés
- Kapcsolódó olvasmány
- Források és szabványok
Why upend and turn coils for material handling
A steel coil is moved and stored in two positions, horizontal for transport and vertical for some processing steps. Turning it at floor level with a machine is safer and quicker than lifting the coil by hand each time.
The upender stands the coil up or lays it flat on its curved support arm. Coil size and weight are confirmed per project.
Mit csinál a gép
The machine is a coil upender with a green base, a curved support arm and a control cabinet at the side. A lifting rig lowers the coil onto the support arm, and the arm tilts to move the coil between horizontal and vertical.
The machine completes the turn at floor level and lowers the coil again when the step is done. Coil size, weight and turning speed are confirmed per project.
Support arm and tilting motion
The curved support arm, painted orange in the footage, holds the coil in an arc as it tilts so the coil stays seated through the movement. The base carries the arm, and the tilting motion is run from the control cabinet on the side.
The operator stands at the cabinet and watches the arm move. Turning angle and speed are confirmed per project.
Ciklus és vezérlés
The operator runs the tilt from the control cabinet, and the arm moves the coil between horizontal and vertical as one smooth movement. The machine stops at the set position and holds the coil there.
The same movement runs the coil back flat after the vertical step. Turn speed and stop positions are confirmed per project.
Amit a felvétel mutat
The footage opens with the lifting rig holding a steel coil above the machine while an operator moves to the control cabinet. The orange support arm takes the coil through a full tilt up to vertical and back to horizontal. The footage is a general demonstration, so your coil size, weight and turning speed are confirmed per project.
Tipikus konfiguráció
Az alábbi ábrák numerikus értékek helyett funkcionális tervezési határokat sorolnak fel, és projektenként megerősítést nyertek.
| Vizsgált paraméter | Tipikus tartomány, projektenként megerősítve |
|---|---|
| Terhelés | steel coils lowered by lifting rig |
| Támogatás | curved arm that holds the coil in an arc |
| Mozgás | tilt between horizontal and vertical |
| Vezérlés | cabinet with buttons and lights |
| Szerelje | floor, in line or in handling area |
| Áramellátás | 380 V háromfázisú 50 Hz, vagy 220 V egyfázisú könnyű gépekhez, projektenként kiválasztva |
Kiválasztási ellenőrzőlista
| Kérdés | Projektenkénti megerősítés |
|---|---|
| Tekercs | külső átmérő, szélesség, súly |
| Pozíció | horizontal or vertical, entry side |
| Mozgás | tilt angle, turn speed |
| Ciklus | turn time, stop positions |
| Weboldal | floor space, access, clearance |
| Áramellátás | feszültség, fázis és frekvencia a helyszínen |
Működés és biztonság
Lower the coil onto the support arm, start the tilt from the control cabinet, and stand clear while the arm moves. Keep hands away from the coil and the support arm while the machine works.
Routine checks cover the support arm, the drive and the control cabinet, per the machine manual. Confirm the coil is seated on the arm before each turn.
Mérnöki GYIK
Q: What does this machine do? A: It tilts a steel coil between horizontal and vertical by moving a curved support arm, so the coil changes position at floor level.
Q: How is the coil loaded? A: A lifting rig lowers the coil onto the support arm, and the arm then tilts by rotating around its pivot to the new position.
Q: Why upend coils with a machine? A: A machine turn keeps the coil supported through the whole movement, so no one has to lift or guide the coil by hand.
Q: What coil sizes suit the machine? A: Coil diameter and weight drive the arm and drive sizing, and the usable range is confirmed per project when you send your coil details.
Q: What does it suit? A: Plants that move coils between horizontal transport and vertical processing, where a floor-level turn saves time and space by avoiding extra lifting.
Következő lépés
- Írj nekünk az info@fhopepack.com címre a tekercs méretével és súlyával.
- We send a coil upending and turning machine proposal within 48 hours.
- We confirm the support arm and turning speed for your coils.
Kapcsolódó olvasmány
- Tekercsek felfordítása és forgatása: Megoldások az ipar számára
- How the coil upender gathers the steel coil from coil car and turns it 90 degrees
- Upender product line
- Hidraulikus felhajtó
Források és szabványok
- ISO 12100:2010 Gépek biztonsága, általános tervezési elvek és kockázatértékelés
- EN 415-10:2014 Csomagológépek biztonsága, általános követelmények
- EN ISO 13849-1:2023 Gépek biztonsága, vezérlőrendszerek biztonsággal kapcsolatos részei
FHOPE coil upending and turning machine demonstration video. Reviewed as a general demonstration; coil size, weight and turning speed confirmed per project.
Utolsó felülvizsgálat: 2026-10-11
