> **Kokkuvõte**
> Dies, moulds and other heavy blocks often have to be turned 90 degrees for maintenance, inspection or storage, and doing it with a crane and chains is slow and risky.
> Our die mould upender and tilter in this video takes the load on an orange tilting cradle on a green base and turns it toward vertical.
> Whether a load can be turned follows from its **weight** and **centre of gravity**. We check both per project.
Sisukord
- Mida videos näidatakse
- Kuidas kallutatav häll töötab
- Koorma kontrollimine
- Kus stantsvormi ümberpööramine aitab
- Juhtimine ja ohutus
- Vormivormi ülespööramise valiku kontrollnimekiri
- Inseneri KKK
- Järgmine samm
- Seotud lugemine
- Allikad
Mida videos näidatakse
Meie ümberpööratav masin seisab tehasehallis: roheline alus kannab oranži ja punast kallutatavat hälli, millel on FHOPE GROUP kaubamärk. Hällil lebab suur kastikujuline koorem.
Hoidik on näidatud erinevate nurkade all, vertikaalselt kallutatud ja hiljem tühjalt alla lastud. Saali taustal seisab masinast eemal sinistes kombinesoonides töötaja. Klambril on ka FHOPE GROUPi logo.
Kuidas kallutatav häll töötab
| Samm | Mis juhtub |
|---|---|
| Load | The load is set on the cradle |
| Secure | The load is held against the cradle faces |
| Tilt | The cradle turns the load toward vertical |
| Unload | The turned load is lifted off |
| Return | The cradle goes back to flat |
Koormus toetub pöörde ajal hälli kahele küljele, seega on see kogu ulatuses toestatud, selle asemel et konksu küljes rippuda.
Koorma kontrollimine
Terasvormi illustreeriv näide:
| Üksus | Väärtus |
|---|---|
| Length × width × height (illustrative) | 1,200 × 800 × 600 mm |
| Volume, 1.2 × 0.8 × 0.6 | 0.576 m³ |
| Steel density | 7,850 kg/m³ |
| Weight if solid, 0.576 × 7,850 | about 4,522 kg |
Päris õõnsustega vorm kaalub vähem. Saatke meile vormi kaal ja joonis ning me kontrollime hälli suurust ja raskuskeset.
Kus stantsvormi ümberpööramine aitab
| Use | What the turn does |
|---|---|
| Mould maintenance | Presents the parting face for cleaning and repair |
| Die change | Turns the die to the press orientation |
| Inspection | Shows the underside without a crane flip |
| Storage | Stands moulds upright to save floor space |
Turning on a cradle replaces crane flips, where the load swings and lands on its edge. For round loads, see our [multipurpose automatic coil tilter with slide table](https://www.fhopepack.com/videos/multipurpose-automatic-coil-tilter-with-slide-table/) and our [large and long coil upenders](https://www.fhopepack.com/videos/large-and-long-coil-upenders-in-real-world-operation/).
Juhtimine ja ohutus
The cradle turns a heavy load. Keep people clear of the cradle and the load's path while it tilts, and stand away from the machine as the worker in our video does.
Kohaldatavad standardid sõltuvad sihtturust. CE-turgude puhul kehtestab ISO 12100 riskihindamise meetodi ja EN 415-10 pakkimismasinate üldised nõuded.
Vormivormi ülespööramise valiku kontrollnimekiri
- [ ] Heaviest die or mould weight.
- [ ] Length, width and height of the largest load.
- [ ] Centre of gravity position.
- [ ] Turning angle needed.
- [ ] How the load arrives: crane or forklift.
- [ ] Põrandapind ja toiteallikas.
Inseneri KKK
Q: What does a die mould upender do?
A: It turns a heavy die or mould toward vertical on a tilting cradle instead of a crane flip.
Q: How do you estimate the weight of a solid steel mould block?
A: Volume times steel density: about 4,522 kg for 1,200 × 800 × 600 mm at 7,850 kg/m³ in our example; a mould with cavities weighs less.
Q: Why is a cradle safer than a crane flip?
A: The load rests on two faces during the turn instead of swinging on a hook.
Q: What should I send for sizing?
A: The heaviest mould weight, its drawing and centre of gravity.
Q: Does anyone stand at the machine during the tilt?
A: No. Keep clear of the cradle and the load's path.
Järgmine samm
Me planeerime teie vormi ülespoole suunatud stantsi kolmes etapis:
1. **Submit your layout drawing** with mould weights, sizes and drawings to **info@fhopepack.com**.
2. **Receive a proposal within 48 hours**, with the cradle size and load check.
3. **Book a site survey** to check crane or forklift access and floor space.
Seotud lugemine
- [Mould upender](https://www.fhopepack.com/mold-upender/)
- [Mould flipper](https://www.fhopepack.com/mold-flipper/)
- [Video: why 90-degree mould upenders are replacing overhead cranes](https://www.fhopepack.com/videos/the-roi-of-safety-why-90-degree-mold-upenders-are-replacing-overhead-cranes-in-industrial-toolrooms/)
Allikad
- Masina sisu: FHOPE insenerimeeskond, 10.10.2026
- Load example: our worked example, illustrative values; steel density 7,850 kg/m³
- Machine in action: [our video on YouTube](https://www.youtube.com/watch?v=AVza0eNbc7o)
- Standardite ulatus: [ISO 12100:2010](https://www.iso.org/standard/51528.html), [EN 415-10:2014](https://www.nen.nl/en/nen-en-415-10-2014-en-191845)
Viimati üle vaadatud: 2026-10-04
