Fabricante y vídeo de la máquina volquete para palets en forma de C

Name: Fabricante de inversores de palets en forma de C y vídeo
Uploaded: 2020-03-27T09:48:11+00:00
Duration: 1 min 46 s
Description: > **Executive summary** > > A C-shape pallet inverter holds the load in the opening of a round C frame and turns it 180°, so the bottom face ends up on top. We build this C-type tilter for pallets, steel sheet stacks, molds and dies. A hydraulic scissor clamp adapts…

Resumen ejecutivo

A C-shape pallet inverter holds the load in the opening of a round C frame and turns it 180°, so the bottom face ends up on top. We build this C-type tilter for pallets, steel sheet stacks, molds and dies. A hydraulic scissor clamp adapts to the load height, a double chain drive with a worm reducer turns the frame, and the frame locks at any angle on emergency stop.

Here the yellow C frame on its green base carries a stack of steel sheets in a fixture. The two halves of the frame, marked A and B, clamp the stack and turn it over, and the operators run the machine from the green control cabinet beside it.

Why a C-shape frame

A round C frame rolls on its rim on rollers in the base, rather than swinging on a centre axle. The load turns about the centre of the ring, so its centre of gravity stays low and close to the turning centre. The drive works on the large rim radius, and the machine needs little more height than the ring itself.

The open side of the C lets a forklift or loading truck put the load in and take it out. With the optional base rotating drive, the C-type tilter can load and unload from the same side, which saves floor space in a narrow aisle.

estructura de la máquina

Parte	Función
C frame (A and B halves)	one rigid ring assembly that rolls on rollers in the base and turns the load 180°
Hydraulic scissor clamp	long-reach scissors clamp a wide range of load heights
Double chain drive with helical gear and worm reducer	turns the frame
Control inversor	fast, stable and safe speed control
Two displacement restrictors	travel limit devices that end the rotation at each end position
Cerraduras	the frame locks at any angle on emergency stop
Panel de control electrónico	separate from the frame
Base rotating drive (option)	turns the machine to load and unload from one side

Ciclo de trabajo

Carga. A forklift sets the pallet or stack into the opening of the C frame.
Abrazadera. The scissor clamp closes onto the load from above.
Vuelta. The frame rolls 180° on its base, driven by the chains.
Lanzamiento. The clamp opens; the load now rests on what was its top face.
Descargar. The forklift takes the load out, from the far side or, with the base rotating option, from the same side.

Worked example: steel sheet stack

Before turning a stack, check its weight against the inverter rating. Steel density is about 7,850 kg/m³.

Paso	Cálculo	Resultado
One sheet, 2,400 × 1,200 × 2 mm	2.4 × 1.2 × 0.002 m³ × 7,850	sobre 45 kg
Stack of 40 sheets	× 40 45	sobre 1,800 kg
Altura de la pila	40 × 2 mm	80 mm, plus the fixture
With a 200 kg fixture (illustrative)	1,800 + 200	sobre 2,000 kg

Resultado. A modest-looking stack of 40 thin sheets already weighs about 2 t with its fixture. Total weight, footprint and stack height decide the inverter size and the clamp stroke, and the rated capacity is confirmed at quote.

Especificaciones

Parámetro	Figura
Active o desactive la	180°
Accionamiento	double chain, helical gear and worm reducer
Abrazadera	hydraulic scissor, adjusts to load height
Control de velocidad	inversor
Seguridad	two displacement restrictors; locks at any angle on emergency stop
Control	panel electronico
Opción	base rotating drive for same-side loading
Capacity, load size, power	confirmado en la cita

Aplicaciones

Pallet loads: changing a pallet or reaching the bottom layer.
Steel sheet stacks: turning to inspect or process the underside.
Molds and dies: turning for assembly, service or storage.
Steel, wire, aluminium and copper coils, and wheel spools.

Lista de verificación de selección

Heaviest load including fixture or pallet.
Load footprint and height range.
Loading from one side or both sides.
Turnos por hora.
Floor space and forklift access.

Seguridad: EN 415-10 e ISO 12100

Load inverters are covered by EN 415-10, with the risk assessment to ISO 12100:2010. The rolling C frame, the scissor clamp and the chain drive are the main hazards. The operator stays at the separate panel, outside the turning zone, during the turn. Two displacement restrictors end the travel, and the frame locks at any angle on emergency stop. Guarding and CE documents are agreed per project.

Preguntas frecuentes sobre ingeniería

Q: Can the C-shape inverter handle steel sheets as well as pallets? A: Yes. It is built for pallets, steel sheet stacks, molds and dies.

Q: What happens if the emergency stop is pressed mid-turn? A: The frame locks at that angle.

Q: Can I load and unload from the same side? A: Yes, with the optional base rotating drive.

Q: How is the load held? A: A hydraulic scissor clamp closes onto the load and adapts to its height.

Q: Does it need a pit? A: No. The base stands on the floor, and the forklift loads into the C opening at base height.

El próximo paso

Send your load size, weight and the reason for turning a info@fhopepack.com.
Nosotros dimensionamos the C frame, clamp and drive.
Respondemos dentro de las 24 horas. con una propuesta y un presupuesto.