Máy đóng gói quỹ đạo hiệu quả 2024

Tóm tắt

An efficient packaging orbital wrapping machine wraps the sides of a tall or unstable pallet load with stretch film while the load stays put on a roller conveyor. The ring rotates around the load, unwinds film from the roll on the arm, and the wrapped pallet exits at the end of the line. This page explains how the layout works, what the demo footage supports, the limits of this version, and the data to send when you ask for sizing.

Mục lục

What this machine class does

Palletized carton loads need a stable outer cover before they travel by truck, sea container or warehouse transfer. A horizontal orbital wrapper is one answer: the ring rotates around the standing pallet and lays stretch film in even layers, keeping the stack tight, dust off the boxes and load stable in transit.

Use this page to decide whether this ring version fits your load flow, and to see which data FHOPE asks for to size one.

How the ring wrap works on a line

The line is a through-type roller conveyor: the palletized load enters, stops in the wrap station, and a horizontal ring arm rotates around it while film unwinds from the roll on the arm. When the programmed number of wraps is complete, the load moves to the exit conveyor and the next load indexes into the station.

Because the load does not turn, the stack keeps its geometry from infeed to outfeed. The ring travels on its circular track, so the stationary wrap zone keeps the load clear of the moving ring while film is applied.

Những gì đoạn phim demo chứng minh

The footage shows a palletized load advancing on a roller conveyor, stopping in the wrap station, the ring arm rotating around the standing load, and the wrapped pallet exiting on the conveyor behind it. Operators assist with load positioning at the infeed, and a mesh safety fence surrounds the wrap station.

It is a general demonstration. It does not show rated capacity, maximum load size, cycle time, or film grade, so those are not listed here as numbers; they are set to your load in the sizing step below.

Kích thước và cấu hình

This machine is sized from your load, not from a fixed rating plate. Confirm the following data with FHOPE when you ask for a proposal:

Dữ liệu để xác nhận Điều nó xác định
Pallet width, length and height (mm) Ring travel diameter and whether the load clears the ring
Trọng lượng tải (kg) Roller conveyor and ring drive duty
Film grade, width and gauge (mm) Film feed and wrap passes
Wrap program (layers, overlap, passes) Cycle time and film cost per pallet
Infeed/outfeed length and transfer height (mm) Conveyor sections and line footprint
Nguồn điện (điện áp, pha, tần số) Drive and control build; house-typical 380 V three-phase 50 Hz, 220 V single-phase option, confirmed on site

Common arrangement points: a mesh fence around the wrap station and a control panel with screen, push buttons and emergency stop. Every row in the table is confirmed to your site conditions before the build.

Where this version stops fitting

A through-type horizontal orbital wrapper is the right shape when loads move in one direction on a line and only the vertical faces need film. Consider the alternatives when one of these is true:

  • The load diagonal is close to or above the ring opening; check the ring clears the tallest, widest load before sizing.
  • The top face must be covered by the same run; a horizontal ring applies film to the sides only, so a top-cover or shrink stage is a separate step.
  • Straps or edge protection must be added; this machine wraps film only.
  • The hall cannot fit a straight conveyor section; a turntable or robot wrapper is the usual fallback for spot wrapping at any pallet, at the cost of a turning step.

Quote the layout drawing and the extremes of your load range, and the reply will state plainly which machine fits.

Câu hỏi thường gặp về kỹ thuật

Q: How does an orbital wrapping machine apply film? A: A horizontal ring arm rotates around the stationary pallet load and unwinds stretch film from a roll carried on the arm.

Q: Does the load turn during wrapping? A: No. The load stays on the conveyor and the ring moves around it, so the stack keeps its orientation from infeed to outfeed.

Q: Can this version put film on top of the load? A: No. The horizontal ring wraps the vertical faces only; a top cover or shrink stage is a separate part of the line.

Q: How many layers of film does the load get? A: The layer count is set on the control panel for the run and is prepared from your load details in the sizing step.

Q: What electrical supply does it need? A: 380 V three-phase 50 Hz is the standard arrangement; light machines can be built for 220 V single phase. Confirm voltage, phase and frequency on site.

Bước tiếp theo: Danh sách kiểm tra yêu cầu báo giá (RFQ)

  1. Email info@fhopepack.com with your pallet size, load height and weight range.
  2. Add a layout drawing of the infeed and outfeed area.
  3. Receive a proposal with ring travel, conveyor sections and wrap program for your loads within 48 hours.
  4. Book a site survey if you want the infeed and outfeed layout checked before the build.

Nguồn và tiêu chuẩn

The standards that apply depend on the destination market. For CE markets, ISO 12100 sets the risk-assessment method and EN 415-10 covers the safety requirements of packaging machines.

Demonstration footage (video yHqayLywzic) reviewed as a general machine demo; rated outputs are not shown in the clip and are therefore not quoted. Last reviewed: 2026-10-18.

bài viết liên quan

Đặt cuộc gọi
Đặt cuộc gọi