Ringkasan Eksekutif Bare metal and plastic pipe need a sealed barrier against moisture, grit and abrasion while they wait outdoors and ride through transit. A tube bagging machine closes a protective polyethylene bag around a single pipe or a bundle, sealing the ends so the contents stay clean. PVC, steel, copper and aluminum pipes all run through the same machine, with sizes and sealing set per project.
Daftar Isi
- What a tube bagging machine does
- The bagging process, step by step
- Bag forming, two ways
- Opsi penyegelan
- Pipes it covers
- Control and parameters
- Konfigurasi khas
- Apa yang ditunjukkan video tersebut
- Daftar periksa pemilihan
- Kontrol dan keamanan
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- Sumber dan standar
What a tube bagging machine does
A tube bagging machine is packaging equipment built for the pipe and tube industry. It encloses a pipe, or a pre-bundled group of pipes, in a polyethylene film bag and seals the ends, so the contents arrive clean and dry.
It suits manufacturers and distributors who ship lengths of PVC, steel, copper or aluminum pipe.
The bagging process, step by step
The cycle runs in sequence. The pipe or bundle is fed into the machine, often on a conveyor. The machine either forms a bag from a roll of film or draws a pre-made bag. The pipe is inserted into the open bag, the end or ends are sealed, the sealed bag is cut from the film, and the finished bundle is discharged ready for storage or shipment.
Bag forming, two ways
A machine can build its own bags from a continuous film roll, which sizes the bag to the pipe as it runs, or it can use pre-made bags. Forming on the machine suits a range of lengths on one line; pre-made bags suit a fixed product. Which approach runs depends on your product mix, per project.
Opsi penyegelan
Bag ends are closed with heat sealing or impulse sealing. A heat sealer holds the film at temperature for the closure; impulse sealing applies a timed pulse of current through the seal bar. Both close a clean end, and the choice follows the film grade and the bag width you run.
Pipes it covers
PVC, steel, copper and aluminum pipes all pass through the same sequence, because the machine handles the bundle envelope rather than the pipe material. The film and the seal settings are what change with the product, and these are confirmed per project.
Control and parameters
The machine runs from a PLC-based panel with a touchscreen, where bag length, seal time and feed speed are set for the product. Length-driven settings let the same line bag a short cut length one run and a full six-meter pipe the next without changing tooling.
Konfigurasi khas
Angka-angka di bawah ini adalah ukuran awal umum untuk kelas mesin ini dan dikonfirmasi per proyek.
| Parameter | Kisaran tipikal, dikonfirmasi per proyek. |
|---|---|
| Rentang pipa | short cut pieces up to 6 m standard lengths, with the bundle envelope confirmed per project |
| Pembentukan tas | on-machine from roll, or pre-made |
| Sealing | heat or impulse, matched to film |
| kontrol | PLC with touchscreen and length settings |
| Umpan | conveyor infeed to match your line |
| Persediaan listrik | Tegangan 380 V tiga fasa 50 Hz, atau 220 V satu fasa untuk stasiun penerangan, dipilih sesuai proyek untuk pasokan listrik pabrik. |
Apa yang ditunjukkan video tersebut
Our footage shows a tube bagging machine feeding a pipe, closing the bag and passing it out. It is a general demonstration, so pipe range, film and line layout for your plant are confirmed with us per project.
Daftar periksa pemilihan
| Pertanyaan | Konfirmasi per proyek |
|---|---|
| Pipe diameters and lengths | machine envelope |
| Single pipes or bundles | infeed design |
| Bag source | on-machine forming or pre-made |
| Film yang sedang digunakan | gauge and seal compatibility |
| Keluaran | bags per hour at your line pace |
| Persediaan listrik | tegangan, fasa, dan frekuensi di lokasi |
Kontrol dan keamanan
The machine runs from a control panel with an emergency stop at the operator position and guarding around the sealing area. Keep hands clear of the feed, the sealing jaws and the cut point while the machine runs. Routine checks cover the seal bars, film path and sensors, per the machine manual.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: Single pipe or bundle? A: The same machine bags a single pipe or a pre-bundled group, with the infeed designed for your product per project.
Q: Heat or impulse sealing? A: Impulse sealing applies a timed current pulse that suits lighter film gauges, while constant heat sealing holds the jaw at temperature for heavy film grades. The choice follows your film specification per project.
Q: Does it need a different setting per pipe size? A: Length and seal settings are stored at the panel, so a size change is a selection rather than tooling.
Q: What materials can it bag? A: PVC, steel, copper and aluminum pipes all run through the machine; the film and settings follow the product.
Q: What lengths are covered? A: Short cut lengths up to full six-meter pipes are handled with the envelope confirmed per project.
Langkah selanjutnya
- Email us at info@fhopepack.com with your pipe range, film and volumes.
- We send bagging options and a layout drawing within 48 hours.
- Kami mengatur survei lokasi untuk mengkonfirmasi lantai dan instalasi utilitas.
Bacaan terkait
- Pengemasan pipa dan tabung plastik: teknologi dan praktik terbaik
- Mesin pemiringan gulungan baja dengan layanan yang disesuaikan.
- Solusi pengumpanan dan pengemasan otomatis batang dan tabung
- Lini produk mesin pengemas FHOPE
Sumber dan standar
- ISO 12100:2010 — Keselamatan mesin. Prinsip umum untuk desain, penilaian risiko, dan pengurangan risiko.
- EN 415-10:2014 — Keselamatan mesin pengemas. Persyaratan umum
- EN ISO 13849-1:2023 — Keselamatan mesin. Bagian-bagian sistem kendali yang berkaitan dengan keselamatan.
- FHOPE tube bagging machine demonstration video. Reviewed as a general demonstration; pipe range, film and layout confirmed per project.
Terakhir ditinjau: 10-10-2026
