Ringkasan Eksekutif A door and panel wrapping machine wraps flat doors and panels in film on a horizontal line and shrinks the film tightly onto the surface in a tunnel. Panels run in on a conveyor, a wrap module lays film over the top, and a heat shrink tunnel seats the film in place. The published controls include a Siemens PLC, real-time tension monitoring and an adjustable overlap from 10 to 50 mm. This guide covers the line flow and the specification range.
Daftar Isi
- Apa yang dilakukan mesin itu
- Bagaimana alur garisnya
- Film and tension control
- Kecilkan terowongan
- Kontrol dan data
- Rentang spesifikasi tipikal
- Daftar periksa pemilihan mesin
- Dasar-dasar pengoperasian dan keselamatan
- Hal-hal penting dalam perawatan
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- Sumber dan standar
Apa yang dilakukan mesin itu
A door and panel wrapping machine wraps flat doors, panels and boards in film on a horizontal line, then shrinks the film onto the surface in a tunnel. The wrap stays tight around the edges and face, protecting the panel finish during handling and long-distance shipping.
Horizontal wrapping suits large, flat products that are awkward on a vertical line or on an orbital stretch wrapper for doors. The panel lies on a conveyor through the whole cycle, so there is no lifting, tipping or rotating. The machine runs at a steady rate alongside a dedicated mesin pengemas susut pintu dan panel mempersiapkan.
Bagaimana alur garisnya
A panel enters on the powered infeed roller conveyor and moves into the wrapping module. Film unwinds from the overhead roll, runs over the top of the panel and is pulled through the press rollers that fold it around the face and edges.
The wrapped panel then travels across the transition section into the shrink tunnel, where rollers carry it through the heated zone. Heat makes the film contract onto the surface, and the finished, tight package leaves at the outfeed for stacking or shipping.
Film and tension control
Package quality depends on how much the film is stretched as it goes over the panel. The machine monitors film tension in real time, and the target is programmable through the control system.
Tension is held consistent across different panel sizes, which keeps the film from wrinkling on a thin panel or from being loose over a heavy one. That same consistent tension is what holds the package stable on the load during transit.
The overlap between film layers is adjustable over a published range of 10 to 50 mm. A tighter overlap strengthens the barrier where dust and moisture could enter, while a smaller overlap saves film on short warehouse-to-dock movements. Both values are programmable through the control system.
Kecilkan terowongan
The shrink tunnel is the finishing stage of the line. It uses a roller conveyor to carry the wrapped panel through a heated zone, and the heat shrinks the stretched film so it seats firmly against the panel edges and corners.
That bonded finish is what keeps the film from slipping during handling and from billowing on the truck. For a customer that wants only a protective cover, the wrap module can run without strict shrink, but the tunnel is what produces the smooth, form-fit package.
Kontrol dan data
The machine runs on a Siemens programmable logic controller with an HMI, and it keeps production counts and statistics for the shift.
The control system sets film tension, overlap and wrap parameters, displays the same values the operator programs, and stores the run counters that feed the line reporting. Safety interlocks are listed in the published control features, and the power supply matches standard industrial 3-phase mains.
Rentang spesifikasi tipikal
The values below are the published ratings of this machine. Confirm the exact numbers against your panel range per project.
| Barang | Spesifikasi |
|---|---|
| Throughput | 15 hingga 20 panel per jam |
| Ukuran panel | hingga 2400 x 1200 x 100 mm |
| Akurasi ketegangan | ± 3% |
| Pengaturan tumpang tindih | 10 hingga 50 mm |
| Kunci pengaman | SIL2 rated (published) |
| Sumber Daya listrik | 380 V, 3-phase, 50/60 Hz |
| Kepatuhan keamanan | ISO 12100, bersertifikat CE |
Daftar periksa pemilihan mesin
Work through these points before you ask for a quote, and we confirm the rest against your panel line per project.
| Barang | Apa yang perlu dikonfirmasi per proyek |
|---|---|
| Panel | panjang, lebar, ketebalan dan berat |
| Film | type, gauge and shrink properties |
| Tumpang tindih | seal strength vs material use |
| Aliran garis | infeed height and outfeed stacking |
| Volume | panels per shift and changeover time |
| Kegunaan | power, and footprint for wrap + tunnel |
| Pemenuhan | target certifications and audits |
Dasar-dasar pengoperasian dan keselamatan
Before a run, confirm the panel width fits the wrap module, the film roll is loaded on the correct unwind, and the tunnel temperature matches the film specification. Feed panels straight onto the conveyor so the film tracks around the edges evenly.
The wrap module is enclosed by a transparent shield that contains film and debris while keeping the cycle visible, and the published control features list SIL2-rated safety interlocks. Operators keep clear of the infeed and outfeed while panels move, and film loading inside the guarded areas follows the lockout procedure in the manual.
Hal-hal penting dalam perawatan
Run the daily checks before the first shift. Confirm the film path is clean, the press rollers turn freely, and the tunnel belts and fans are free of film scraps.
Keep the unwind, the transfer and the tunnel conveyor running surfaces clean, and wipe the pinch rollers so tension stays even panel to panel. Watch the HMI for tension and temperature faults, and follow the maintenance schedule in the manual for the tunnel heating elements.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: What size panels can the machine wrap? A: The published rating covers panels up to 2400 x 1200 x 100 mm, with the exact range confirmed per project.
Q: How fast does the packaging line run? A: The published throughput is 15 to 20 panels per hour, including the wrap and shrink steps; confirm the rating against your panel batch per project.
Q: How is film tension controlled? A: Real-time tension monitoring holds the film stretch to a published accuracy of ±3%, with the target programmed on the control system.
Q: Can the overlap be adjusted? A: Yes. The published overlap range is 10 to 50 mm, set through the control system per panel type.
Q: What does the shrink tunnel do? A: It passes the wrapped panel through a heated zone so the film shrinks tightly onto the surface, forming a smooth, bonded package.
Q: What electrical supply does the line require? A: The machine operates on a standard 380 V, 3-phase, 50/60 Hz power supply.
Q: What safety features are incorporated? A: The published features list SIL2-rated safety interlocks and transparent protective guarding, with ISO 12100 and CE certification.
Q: What production metrics does the PLC track? A: The PLC and HMI track production counts, run counters and shift statistics, alongside tension and temperature status.
Langkah selanjutnya
- Email us at info@fhopepack.com with your panel sizes, film type and target throughput.
- Kami akan mengirimkan gambar tata letak dan proposal pembungkus dalam waktu 48 jam.
- We arrange a site survey to confirm the infeed, tunnel length and power before installation.
Bacaan terkait
- Door and wooden board shrink wrapping machine
- Panel stretch wrapping with film applicator
- Good price door shrink wrapping machine
- Precision orbital wrapping for extra-long panels
- Lini produk mesin pengemasan FHOPE
Sumber dan standar
- ISO 12100:2010 — Keselamatan mesin. Prinsip umum untuk desain, penilaian risiko, dan pengurangan risiko.
- EN 415-10:2014 — Keselamatan mesin pengemas. Persyaratan umum
- EN ISO 13849-1:2023 — Keselamatan mesin. Bagian-bagian sistem kendali yang berkaitan dengan keselamatan.
- FHOPE door and panel wrapping machine demonstration video, YouTube.
Terakhir ditinjau: 09-10-2026
