{"id":17369,"date":"2026-08-18T17:40:14","date_gmt":"2026-08-18T09:40:14","guid":{"rendered":"https:\/\/www.fhopepack.com\/zh\/?p=17369"},"modified":"2026-08-18T17:40:14","modified_gmt":"2026-08-18T09:40:14","slug":"automatic-aluminum-tube-bagging-stacking-line-one-stop-solution-for-bagging-sealing-palletizing","status":"publish","type":"post","link":"https:\/\/www.fhopepack.com\/zh\/automatic-aluminum-tube-bagging-stacking-line-one-stop-solution-for-bagging-sealing-palletizing\/","title":{"rendered":"Automatic Aluminum Tube Bagging &#038; Stacking Line \u2013 One-Stop Solution for Bagging, Sealing &#038; Palletizing"},"content":{"rendered":"<p><strong>Summary:<\/strong> The requested shrink-bagging line \u2014 3\u20134 m infeed conveyor, sealing machine, shrink tunnel, and 3\u20134 m outfeed conveyor \u2014 can package all six listed pipe and gutter cross-sections on one machine by switching folded-film widths. The recurring trade-off is 80\u2013100 mm of web width trimmed per 3 m package, equal to 0.24\u20130.30 m\u00b2 of film scrapped per cycle. A horizontal flow-pack alternative reduces that waste, but only if a supplier-quoted film width and a bundle-stability trial confirm the saving.<\/p>\n<h2>\ud83d\udee0\ufe0f Product Matrix and Line Design Constraints<\/h2>\n<iframe width=\"100%\" height=\"420\" src=\"https:\/\/www.youtube.com\/embed\/iZHlVd17VpU?rel=0\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture\" allowfullscreen><\/iframe>\n<p><strong>The line must handle six cross-sections \u2014 pipes at 90, 100 and 150 mm; gutters at 125, 150 and 185 mm; plus a 20\u00d740 mm flat-oval pipe pair \u2014 in 3 m and 1 m lengths, with pipes running individually and gutters in bundles, all on one sealing machine with width changeover between sizes.<\/strong><\/p>\n<p>The supplied scope is a mixed-profile production schedule, not a single-product line. Pipes at 90 mm, 100 mm and 150 mm run single-file, while gutters at 125 mm, 150 mm and 185 mm are grouped into bundles. Product length is predominantly 3 m, with a secondary 1 m pipe length running on the same line.<\/p>\n<p>No single folded film web (film supplied flat, folded in half) can serve every cross-section without adjustment. The arithmetic is instructive: a 180 mm folded web opens into a tube of roughly 360 mm circumference, while a 20\u00d740 mm pair carries a perimeter of only about 120 mm. That mismatch is why every shrink-bagging cycle produces trim waste (film edge cut off and discarded) \u2014 the film is bought wider than the product demands so the sealing machine can grip it.<\/p>\n<table>\n<thead>\n<tr>\n<th>Product<\/th>\n<th>Cross-section<\/th>\n<th>Running mode<\/th>\n<th>Lengths<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Pipes<\/td>\n<td>90 \/ 100 \/ 150 mm<\/td>\n<td>Individual<\/td>\n<td>3 m + 1 m<\/td>\n<\/tr>\n<tr>\n<td>Gutters<\/td>\n<td>125 \/ 150 \/ 185 mm<\/td>\n<td>Bundled<\/td>\n<td>3 m<\/td>\n<\/tr>\n<tr>\n<td>Flat-oval pair<\/td>\n<td>20\u00d740 mm<\/td>\n<td>Individual pair<\/td>\n<td>3 m<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Changeover between these six sizes is therefore a core design variable, not an occasional event. Each size change touches at least one of three machine settings: folded-film width, infeed guides, and \u2014 on a flow-pack line \u2014 the former (collar that folds film around the product).<\/p>\n<h2>\ud83c\udfd7\ufe0f Evaluation Criteria<\/h2>\n<p><strong>Grade both lines on five identical criteria \u2014 film waste per package, throughput at 3 m product length, single-pipe versus bundle capability, conveyor floor space, and changeover between six product sizes \u2014 and weight film waste highest because it repeats on every production cycle, not just at purchase.<\/strong><\/p>\n<p>Film waste earns the highest weight because it is a recurring consumable loss. The 80\u2013100 mm trim occurs on every cycle, every shift, and every batch; a machine investment is paid once. The remaining four criteria \u2014 throughput, bundle capability, floor space, and changeover \u2014 determine whether the line can hold the required schedule, but none of them consumes material on each cycle.<\/p>\n<table>\n<thead>\n<tr>\n<th>Criterion<\/th>\n<th>Why it determines the decision<\/th>\n<th>Suggested weight<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Film waste per package<\/td>\n<td>80\u2013100 mm trim repeats on every cycle<\/td>\n<td>High<\/td>\n<\/tr>\n<tr>\n<td>Single-pipe vs. bundle capability<\/td>\n<td>Pipes run one-up; gutters run as bundles<\/td>\n<td>High<\/td>\n<\/tr>\n<tr>\n<td>Throughput at 3 m length<\/td>\n<td>Total line length sets the practical cycle rate<\/td>\n<td>Medium<\/td>\n<\/tr>\n<tr>\n<td>Conveyor floor space<\/td>\n<td>Infeed + machine + outfeed must fit the bay<\/td>\n<td>Medium<\/td>\n<\/tr>\n<tr>\n<td>Changeover effort<\/td>\n<td>Film width changes across all six sizes<\/td>\n<td>Medium<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>A straight weight applied to film waste exposes the core difference between the two options: Option A accepts a certain material loss; Option B is bought to reduce it, but carries its own verification risk.<\/p>\n<h2>\ud83d\udcc8 Option A: Shrink Bagging Line<\/h2>\n<p><strong>Option A \u2014 the requested line with 3\u20134 m infeed conveyor, sealing machine, shrink tunnel, and 3\u20134 m outfeed conveyor \u2014 packages all six product sizes on one machine, but the operator must change folded film width for each cross-section, and every package carries an unavoidable 80\u2013100 mm trim waste.<\/strong><\/p>\n<p>The line operates as a continuous sequence: infeed conveyor, intermittent jaw sealer, shrink tunnel (heated chamber that shrinks film tight), and outfeed conveyor to stacking or palletizing. Both options in this evaluation should carry CE marking per Machinery Directive 2006\/42\/EC, with safety-related control circuits specified to ISO 13849-1 \u2014 request this documentation with every quote.<\/p>\n<p>The film economics come directly from the supplied dialogue:<\/p>\n<table>\n<thead>\n<tr>\n<th>Parameter<\/th>\n<th>Value (from supplied context)<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Folded web width for 20\u00d740 mm pipe pair<\/td>\n<td>180 mm<\/td>\n<\/tr>\n<tr>\n<td>Useful film covering the product<\/td>\n<td>80\u2013100 mm<\/td>\n<\/tr>\n<tr>\n<td>Side allowance consumed by the sealing drive<\/td>\n<td>~100 mm<\/td>\n<\/tr>\n<tr>\n<td>Trim waste per 3 m package<\/td>\n<td>80\u2013100 mm of web width<\/td>\n<\/tr>\n<tr>\n<td>Film area scrapped per 3 m package<\/td>\n<td>0.24\u20130.30 m\u00b2 (trim width \u00d7 3 m length)<\/td>\n<\/tr>\n<tr>\n<td>Film area scrapped per 10,000 packages<\/td>\n<td>2,400\u20133,000 m\u00b2 \u2014 the area of a web 800\u20131,000 m long and 3 m wide<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Key Point:<\/strong> The sealing machine needs roughly 100 mm of film width just for the sealing drive. That film never touches the product \u2014 it is trimmed and scrapped on every cycle. The trimmed portion alone represents 44\u201356% of the purchased 180 mm web width.<\/p>\n<p>The 0.24\u20130.30 m\u00b2 per package figure is the number to convert into a monthly cost. Multiply it by your film price per square metre and by monthly package volume; the supplier&#8217;s film-width datasheet should be stated in writing before purchase, since this arithmetic is derived from the supplied 180 mm figure.<\/p>\n<p>Typical shrink film for pipe and gutter packaging runs at 50\u201380 \u00b5m gauge, with 2\u20134 seconds residence in the tunnel at roughly 150\u2013200\u00b0C \u2014 verify the exact film specification with your supplier, as gauge affects both shrink force and cost per square metre.<\/p>\n<p>Option A suits a plant that wants a proven layout, tolerates bundle shape variation, and already budgets for film scrap. The machine cost data was not supplied; do not assume it is cheaper until you hold quotes from at least two vendors.<\/p>\n<h2>\ud83d\udee1\ufe0f Option B: Horizontal Flow Packing<\/h2>\n<p><strong>Option B \u2014 the horizontal flow-pack line \u2014 wraps film closely around each 3 m pipe or bundle profile, eliminating most of the 80\u2013100 mm trim waste that shrink bagging generates every cycle, but it needs a longer forming section, tighter bundle tolerances, and more careful changeover across six product sizes.<\/strong><\/p>\n<p>The supplier&#8217;s stated logic is direct: for less waste, horizontal flow packing is a material-saving alternative. A flow-pack line forms film around the product in continuous motion \u2014 the former folds flat film into a tube, a longitudinal fin seal closes it with a seal lap (overlap where the film is fused, typically 10\u201320 mm), and rotating end-seal jaws cut and seal each package. Film width is matched to the product perimeter instead of a fixed folded web.<\/p>\n<p>For the 20\u00d740 mm flat-oval pipe pair, a flow-pack former requires an unfolded film width close to the product perimeter plus the seal lap and a small trim margin \u2014 a meaningful reduction from the 180 mm folded web. The exact figure is supplier-specific; no width is stated in the supplied context, so the saving cannot be quantified until the vendor issues a film-width calculation.<\/p>\n<table>\n<thead>\n<tr>\n<th>Trade-off<\/th>\n<th>What changes vs. Option A<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Film consumption<\/td>\n<td>Drops, because film is matched to the profile<\/td>\n<\/tr>\n<tr>\n<td>Machine length<\/td>\n<td>Grows; former and sealing section add length<\/td>\n<\/tr>\n<tr>\n<td>Changeover effort<\/td>\n<td>Former or width adjustment per size, more steps<\/td>\n<\/tr>\n<tr>\n<td>Bundle handling<\/td>\n<td>Cross-section must stay stable through the former<\/td>\n<\/tr>\n<tr>\n<td>Speed profile<\/td>\n<td>Continuous motion suits uniform profiles<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Key Point:<\/strong> Flow packing rewards uniform shapes. Pipes at 90 mm, 100 mm and 150 mm are ideal. A 185 mm gutter bundle will likely need strapping (ASTM D3950-class strapping, verified with your vendor) so the film forms cleanly without snagging \u2014 treat this as an assumption until confirmed by a trial.<\/p>\n<p>Two risks require explicit supplier verification. First, the former and sealing rollers may need a reinforced infeed to carry a rigid 3 m gutter without bending it \u2014 ask the supplier for a rigidity test result at full length. Second, changeover complexity rises: a film-roll swap on a shrink line is routine, but flow-pack former changes add setup steps, and the time is machine-specific. Request a live changeover demonstration across all six sizes before committing.<\/p>\n<h2>\u2699\ufe0f Comparison Table<\/h2>\n<p><strong>The comparison below scores Option A and Option B on the same five evaluation criteria \u2014 film waste, throughput at 3 m, bundle capability, floor space, and changeover \u2014 using supplied specifications where available and flagging every estimate, so the decision rests on equal evidence for both lines.<\/strong><\/p>\n<h3>Primary evaluation \u2014 five decision criteria<\/h3>\n<table>\n<thead>\n<tr>\n<th>Evaluation criterion<\/th>\n<th>Option A: Shrink bagging<\/th>\n<th>Option B: Horizontal flow packing<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Film waste per package<\/td>\n<td>80\u2013100 mm of web width per 3 m package (0.24\u20130.30 m\u00b2) \u2014 stated in supplied context<\/td>\n<td>Not quantified in supplied context; film is formed to the profile, so trim is expected lower \u2014 obtain the vendor&#8217;s width-and-trim calculation before comparing<\/td>\n<\/tr>\n<tr>\n<td>Throughput at 3 m product length<\/td>\n<td>No cycle time in supplied context; intermittent jaw sealing typically 3\u20136 packages\/min at 3 m (estimate \u2014 verify in factory test)<\/td>\n<td>No cycle time in supplied context; continuous motion typically 6\u201312 packages\/min (estimate \u2014 verify in factory test)<\/td>\n<\/tr>\n<tr>\n<td>Single-pipe vs. bundle capability<\/td>\n<td>Pipes single, gutters bundled; shrink film conforms to variable bundle shapes (trial recommended)<\/td>\n<td>Pipes single, gutters bundled; 185 mm bundles likely need strapping to hold cross-section \u2014 verify with vendor<\/td>\n<\/tr>\n<tr>\n<td>Conveyor floor space<\/td>\n<td>3\u20134 m infeed + machine + 3\u20134 m outfeed \u2248 8\u201310 m total, from supplied conveyor lengths<\/td>\n<td>Not stated; former and sealing rollers add length \u2014 request a dimensioned layout drawing<\/td>\n<\/tr>\n<tr>\n<td>Changeover between six sizes<\/td>\n<td>Folded-film roll swap per size; measured in minutes, machine-specific<\/td>\n<td>Former change or width adjustment per size; more steps \u2014 request a live demonstration<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3>Other considerations<\/h3>\n<table>\n<thead>\n<tr>\n<th>Consideration<\/th>\n<th>Option A<\/th>\n<th>Option B<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Relative investment<\/td>\n<td>Not provided in supplied context \u2014 obtain quotes from at least two vendors before comparing cost<\/td>\n<td>Not provided in supplied context \u2014 obtain quotes from at least two vendors before comparing cost<\/td>\n<\/tr>\n<tr>\n<td>Operator skill<\/td>\n<td>Standard sealing-and-shrink experience (assumption \u2014 confirm in the training proposal)<\/td>\n<td>Flow-pack setup and former-change experience (assumption)<\/td>\n<\/tr>\n<tr>\n<td>Effective film utilisation<\/td>\n<td>Roughly 80\u2013100 mm of 180 mm web covers product; remainder is sealing allowance and trim<\/td>\n<td>Expected higher, but unquantified until the vendor issues a film-width drawing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>\ud83d\udee0\ufe0f Selection Advice<\/h2>\n<p><strong>Choose Option A when purchase risk, floor-space limits, and operator retraining outweigh film cost; choose Option B only after a supplier-quoted film width and a paid trial run with a 185 mm gutter bundle confirm the material savings actually materialize on your line.<\/strong><\/p>\n<p>Option B savings depend entirely on two unverified inputs: the official film-width quote and bundle stability under real line speed. Until both are confirmed, Option B&#8217;s material advantage is a hypothesis, not a specification. To resolve it, commission a paid trial run with a 185 mm gutter bundle at 3 m length on the flow-pack former and measure the actual trim per package.<\/p>\n<table>\n<thead>\n<tr>\n<th>If this describes your plant<\/th>\n<th>Choose<\/th>\n<th>Reason<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Film cost is the dominant monthly consumable<\/td>\n<td>Option B \u2014 after verification<\/td>\n<td>The saving is real only if the official width quote and the 185 mm bundle trial confirm it<\/td>\n<\/tr>\n<tr>\n<td>185 mm gutters arrive with variable stacking<\/td>\n<td>Option A<\/td>\n<td>Shrink film forgives bundle shape variation (assumption based on film compliance)<\/td>\n<\/tr>\n<tr>\n<td>Floor space is fixed at \u2248 8\u201310 m<\/td>\n<td>Option A<\/td>\n<td>Conveyor lengths are stated in the supplied context; Option B&#8217;s extra length must be proven with a layout drawing<\/td>\n<\/tr>\n<tr>\n<td>Mostly uniform pipes, few size changes<\/td>\n<td>Option B<\/td>\n<td>Continuous motion rewards uniform profiles, provided bundles hold shape<\/td>\n<\/tr>\n<tr>\n<td>Crew has only sealing-and-shrink experience<\/td>\n<td>Option A<\/td>\n<td>Flow-pack setup adds a new skill set (assumption \u2014 confirm in training scope)<\/td>\n<\/tr>\n<tr>\n<td>Investment data is still missing<\/td>\n<td>Neither \u2014 request quotes first<\/td>\n<td>Supplied context contains no cost data; two vendor quotes are required before either option can be costed<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><strong>Key Point:<\/strong> The decisive question is not which machine is &#8220;better.&#8221; It is whether film scrap or floor space hurts your operation more. The waste on Option A is certain \u2014 0.24\u20130.30 m\u00b2 per package \u2014 while Option B&#8217;s savings remain unquantified until the vendor and a trial put numbers on it.<\/p>\n<h2>\ud83c\udfd7\ufe0f Verify Before You Buy<\/h2>\n<p><strong>Before committing to Option B, obtain written answers to three questions: the exact flow-pack film width for the 20\u00d740 mm pipe pair, the total installed line length including the former, and the maximum bundle cross-section the former accepts without collapse.<\/strong><\/p>\n<ol>\n<li>\n<p><strong>Exact film width<\/strong> \u2014 What unfolded film width does the former require for the 20\u00d740 mm flat-oval pair, and what is the resulting trim waste per 3 m package?<\/p>\n<\/li>\n<li>\n<p><strong>Total installed length<\/strong> \u2014 What is the full line length with former, sealing section, and outfeed, and will it fit your measured bay?<\/p>\n<\/li>\n<li>\n<p><strong>Maximum bundle cross-section<\/strong> \u2014 What is the largest bundle profile the former accepts, and will a 185 mm gutter bundle pass through without collapsing or snagging?<\/p>\n<\/li>\n<\/ol>\n<p>Require written answers before choosing Option B. If the vendor cannot supply item 1 or item 3 in writing, Option A remains the defensible default.<\/p>\n<h2>\ud83d\udcc8 Purchase-Decision Checklist<\/h2>\n<p><strong>Work through this checklist only after you have obtained written supplier confirmation of the 180 mm folded-web specification, the 80\u2013100 mm trim liability, the flow-pack film width for the 20\u00d740 mm pair, and the total installed length of both line options.<\/strong><\/p>\n<ul>\n<li>\n<p>[ ] Confirm the 180 mm folded-web figure and the 80\u2013100 mm trim waste against your actual film rolls and the supplier&#8217;s datasheet.<\/p>\n<\/li>\n<li>\n<p>[ ] Assign an owner for film-width changeover and time a full six-size changeover sequence on each line.<\/p>\n<\/li>\n<li>\n<p>[ ] Measure the available bay: Option A is \u2248 8\u201310 m per the supplied conveyor lengths; Option B needs a dimensioned layout drawing.<\/p>\n<\/li>\n<li>\n<p>[ ] Run a paid trial with a 185 mm gutter bundle at 3 m length on the flow-pack former, at line speed.<\/p>\n<\/li>\n<li>\n<p>[ ] Obtain the official Option B film width and per-package trim for the 20\u00d740 mm pair.<\/p>\n<\/li>\n<li>\n<p>[ ] Confirm the mixed 3 m and 1 m length schedule runs in one shift without re-tooling.<\/p>\n<\/li>\n<li>\n<p>[ ] Request the CE declaration of conformity (Machinery Directive 2006\/42\/EC) and ISO 13849-1 safety documentation with both quotes.<\/p>\n<\/li>\n<li>\n<p>[ ] Convert the waste math into monthly cost: 0.24\u20130.30 m\u00b2 per package \u00d7 monthly volume \u00d7 film cost per m\u00b2.<\/p>\n<\/li>\n<\/ul>\n<p><em>Related products: The <a href=\"https:\/\/www.fhopepack.com\/Automatic-Steel-Tube-Packing-Line\/\">Automatic Steel Tube Packing Line<\/a> uses the same bagging-and-sealing logic and can serve as an additional layout reference. It is not part of the decision matrix above.<\/em><\/p>\n<h2>\ud83d\udee1\ufe0f FAQ<\/h2>\n<p><strong>These FAQ answers cover the three questions that most often decide the purchase \u2014 whether one machine handles all six product sizes, why the 80\u2013100 mm trim waste is unavoidable on shrink bagging, and whether horizontal flow packing always delivers lower running cost.<\/strong><\/p>\n<p><strong>Can one machine really package all six product sizes?<\/strong>\nYes. Based on the supplied context, a single shrink-bagging line handles pipes at 90 mm, 100 mm and 150 mm, gutters at 125 mm, 150 mm and 185 mm, plus the 20\u00d740 mm pipe pair. The operator switches folded-film width between sizes; Option B requires former or width adjustment instead.<\/p>\n<p><strong>Why is 80\u2013100 mm of film wasted on every package?<\/strong>\nThe sealing drive needs roughly 100 mm of side allowance that never contacts the product, and the surplus web beyond the product profile is trimmed and scrapped. In the supplied dialogue, the supplier confirmed this extra width is waste. Per 3 m package, that trim equals 0.24\u20130.30 m\u00b2 of film; over 10,000 packages, 2,400\u20133,000 m\u00b2.<\/p>\n<p><strong>Is horizontal flow packing always cheaper to run?<\/strong>\nNo. Flow packing uses less film, but the supplied context contains no investment figures, no flow-pack film width, and no bundle-stability test for the 185 mm gutter. Run the math \u2014 0.24\u20130.30 m\u00b2 per package \u00d7 monthly volume \u00d7 film cost per m\u00b2 \u2014 and compare it against at least two vendor quotes and the paid trial result before switching.<\/p>","protected":false},"excerpt":{"rendered":"<p>Summary: The requested shrink-bagging line \u2014 3\u20134 m infeed conveyor, sealing machine, shrink tunnel, and 3\u20134 m outfeed conveyor \u2014 can package all six listed pipe and gutter cross-sections on one machine by switching folded-film widths. The recurring trade-off is 80\u2013100 mm of web width trimmed per 3 m package, equal to 0.24\u20130.30 m\u00b2 of [&hellip;]<\/p>","protected":false},"author":1,"featured_media":17402,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_seopress_robots_primary_cat":"none","_seopress_titles_title":"","_seopress_titles_desc":"The line must handle six cross-sections \u2014 pipes at 90, 100 and 150 mm; gutters at 125, 150 and 185 mm; plus a 20\u00d740 mm flat-oval pipe pair \u2014 in 3 m and 1 m lengths, with pipes running individually and gutters in bundles, all on one sealing machine with width changeover between sizes.","_seopress_robots_index":"","fifu_image_url":"https:\/\/www.fhopepack.com\/blog\/wp-content\/uploads\/2018\/04\/Aluminum-packing-line.jpg","fifu_image_alt":"","footnotes":""},"categories":[1404,1],"tags":[],"class_list":["post-17369","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-automatic-aluminum-tube-bagging-stacking-line","category-uncategorized"],"amp_enabled":true,"_links":{"self":[{"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/posts\/17369","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/comments?post=17369"}],"version-history":[{"count":2,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/posts\/17369\/revisions"}],"predecessor-version":[{"id":17403,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/posts\/17369\/revisions\/17403"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/media\/17402"}],"wp:attachment":[{"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/media?parent=17369"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/categories?post=17369"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.fhopepack.com\/zh\/wp-json\/wp\/v2\/tags?post=17369"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}