执行摘要 Our FPFZ-C02 pallet inverter holds the load between two clamps and turns it 180 degrees, so the pallet can be changed from the top. It takes loads up to 2.0 t and 610 to 2,000 mm high, in about 25 s per turn. Two clamps close from both sides, which shortens the clamping stroke and grips heavy loads evenly. A worked example checks a wrapped roll against the clamp range and works out turns per hour.
目录
- Why turn a load upside down
- What the second clamp adds
- The clamp and turn cycle
- FPFZ-C02 specifications
- Worked example: a wrapped roll on a damaged pallet
- 选择清单：我们需要发送哪些内容
- 安全与 EN 415-10
- 工程常见问题解答
- 下一步
- 相关阅读
- 来源
Why turn a load upside down
A heavy load sitting on the wrong pallet is hard to move off it. It may be on a damaged pallet, a wooden one that cannot enter a clean area, or a pool pallet that must go back.
An inverter solves this by turning the whole load over. A new pallet goes on top first. After a 180 degree turn, the load sits on the new pallet, and the old one is now on top, free to lift away.
What the second clamp adds
A single clamp inverter presses the load down onto a fixed platform. Our dual clamp design moves both the top and the bottom clamp towards the load. Each clamp then travels only part of the gap, so clamping is quicker.
Gripping from both sides also centres the load in the frame. That keeps a heavy or tall load balanced through the turn, with no vibration as it goes over.
The clamp and turn cycle
- 加载。 A forklift sets the load in the frame, and a new pallet is placed on top of it.
- 夹钳。 The two clamps close on the old pallet below and the new pallet above.
- 转动。 The frame turns the clamped stack through 180 degrees.
- 发布。 The clamps open. The load now stands on the new pallet.
- 去掉。 The old pallet is lifted off the top, and the forklift takes the load away.
The operator runs the cycle from the panel or a wireless remote, outside the fence.
FPFZ-C02 specifications
| 名称 | FPFZ-C02 |
|---|---|
| 托盘尺寸 | 1,000–1,200 × 1,000–1,200 毫米 |
| Load height in clamps | 610–2,000毫米 |
| 营业额 | 2.0吨 |
| 周转时间 | 大约25秒 |
| 翻转角 | 180° |
| 车架 | welded A3 steel profile, dead-weight fixing |
| 通过积极争取让商标与其相匹配的域名优先注册来维护 | 面板或无线遥控器 |
| 电机功率 | 约4.0千瓦 |
| 电源供应 | 380伏，50/60赫兹，三相 |
| 机器尺寸 | 约 2,200 × 1,450 × 2,000 毫米（长 × 宽 × 高） |
Worked example: a wrapped roll on a damaged pallet
Take a wrapped roll 1,000 mm in diameter and 1,200 mm long, standing on end on a 1,200 × 1,200 mm pallet. The pallet is damaged and must be changed. Each pallet is 150 mm high, and the roll material weighs about 800 kg/m³. These are illustrative customer figures.
重量。 The roll volume is π × 0.5² × 1.2 = 0.94 m³, so it weighs about 0.94 × 800 = 754 kg. That is well inside the 2.0 t capacity.
Clamp range. The clamps hold the old pallet, the roll and the new pallet together. That stack is 150 + 1,200 + 150 = 1,500 mm high. It sits inside the 610–2,000 mm range, with 500 mm to spare.
每小时转数。 One turn takes about 25 s, so the machine alone could make 3,600 ÷ 25 = 144 turns an hour. Forklift trips and placing the new pallet add time t at your site. If t is 90 s, an illustrative figure, that is 3,600 ÷ (25 + 90) = 31 loads an hour.
选择清单：我们需要发送哪些内容
- 托盘的长度和宽度。
- Load height, including both pallets.
- Load weight and shape.
- 每小时装载量。
- Floor space and forklift access.
- 现场供电。
安全与 EN 415-10
We design the inverter to EN 415-10 for packaging machines and assess risks to ISO 12100. The turning frame and the closing clamps are the main hazards. A yellow mesh fence keeps people out of the turning zone. On our dual clamp inverters, mechanical and electrical stop blocks guard against overload, and a current limiting valve controls the lowering speed. The control circuit runs at AC 24 V.
工程常见问题解答
Q: When do I need dual clamps rather than one? A: For heavy, tall or round loads that must stay centred, and where clamping time matters.
Q: Can the inverter take round loads such as rolls? A: Yes, if the load stands on a pallet and the stack height fits the clamp range.
Q: Is the machine bolted down? A: Yes. The frame is fixed to the floor by bolts.
问：适用哪些安全标准？答：在CE市场，风险评估适用ISO 12100标准，机器适用EN 415-10标准。
下一步
- Email your pallet sizes, load heights and weights 至 info@fhopepack.com.
- 我们会在24小时内回复并提供方案。 naming the inverter model.
- 我们发送一份布局图 with the fence and forklift access.
相关阅读
- Pallet inverter with two clampers, 2 t
- Floor-level dual clamp pallet inverter
- Heavy-duty 180° pallet changer machine
- Steel sheet pallet changing upender
来源
- Specifications: FHOPE pallet inverter with two clampers (FPFZ-C02) and floor-level pallet inverter product pages
- 机器视频： pallet inverter with dual clamper on YouTube
- Weight, clamp range and output: our worked example, illustrative load figures
- 标准：EN 415-10（包装机械，通用安全）；ISO 12100:2010
上次审核日期： 2026年10月17日
