执行摘要 A coil tilter with a sliding table turns a coil or packed load 90° and lets the table travel out for loading by crane or fork-lift. In this clip our C-shaped tilter turns a film-wrapped load from upright to on its side between about 16 s and 40 s, then swings it back by about 56 s. Our mechanical upender with sliding table is rated for 5 T, single-way 90° turn-over, about L3000 × W2200 × H2600 mm, configured per project.
目录
- 视频片段按顺序展示了以下内容
- What a sliding-table coil tilter does
- Turn and return cycle time on the clip
- Specifications of our sliding-table upender
- 节拍检查
- Selection checklist for a coil tilter with sliding table
- 控制与安全
- 工程常见问题解答
- 下一步
- 相关阅读
- 来源
视频片段按顺序展示了以下内容
The clip shows one machine from one camera position: a yellow C-shaped frame, open on one side, standing on a heavy blue base. A film-wrapped load sits inside the C. Each end of the frame has a round lifting lug.
- 0 到 12 秒。 The load rests upright on the table and nothing moves.
- 大约16秒。 The frame starts to turn about its lower pivot and the load leans with it.
- 大约 20 到 32 秒。 The turn continues until the load lies on its side, held between the two arms of the C.
- 大约 36 到 40 秒。 The frame reaches the end of its turn, with the opening of the C facing up.
- 大约 44 到 56 秒。 The frame swings back and the load returns close to its upright starting attitude.
The table stays in its turning position throughout this sequence; table travel belongs to loading and unloading, before and after the turn.
What a sliding-table coil tilter does
A coil tilter turns a load through 90° between lying on its face and standing on its side. The sliding table adds one more function: the table on the base runs on rails, so it can travel out from under the frame for loading and unloading and travel back for the turn. That keeps the crane hook or the fork-lift away from the frame while the load is placed.
The C-shaped frame holds the load on two faces, the table and the back of the C. The load turns with the frame instead of sliding across it, which protects edges and film wrapping.
| Tilter element | 按尺寸 |
|---|---|
| C-frame opening | Load height and width |
| Sliding table and rails | Load footprint and loading method |
| Pivot and drive | Load moment at 5 T |
| 吊耳 | Moving and installing the frame |
Turn and return cycle time on the clip
| 踩下夹子 | 时间窗口 | 修读年限 |
|---|---|---|
| At rest before the turn | 0 到大约 12 秒 | 大约12秒 |
| Turn from upright to on its side | 大约16到40秒 | 大约24秒 |
| Return toward upright | 大约44到56秒 | 大约12秒 |
The turn on the clip is slower than the return, which is usual: the drive slows the load into its side position, while the return carries less risk. Our page model is specified for a single-way 90° turn-over, where the frame turns the load once and the load leaves in its new attitude. The clip shows the frame returning, which is the two-way pattern. We choose one-way or two-way at the layout stage, because it changes the cycle.
Specifications of our sliding-table upender
| 带滑动台的翻转器和倾斜器 | 规格 |
|---|---|
| 最大加载 | 5 T |
| 周转 | 90°，单向 |
| 机器尺寸 | about L3000 × W2200 × H2600 mm |
| 整机重量 | 约4吨 |
| 电源电压 | 交流 380 伏，60 赫兹 |
节拍检查
For an illustrative target of 30 loads per hour, one load must leave every 120 s, from 3,600 ÷ 30. On the clip the turn takes about 24 s and the return about 12 s, about 36 s of motion. That leaves about 84 s for sliding the table out, unloading, loading, sliding it back and letting the load settle. When the table travel and the crane or fork-lift move fit in that window, one tilter covers the target.
Selection checklist for a coil tilter with sliding table
- Load OD, width or footprint, and weight up to 5 T.
- 到达时的态度以及下一站需要的态度。
- One-way turn-over, or turn and return.
- Loading method: crane, fork-lift or conveyor, and the table travel needed.
- Floor space for about L3000 × W2200 × H2600 mm, plus the table travel, which we fix at the layout stage.
- Takt, including table travel and loading.
控制与安全
The swing of the C-frame and the travel of the sliding table are the danger zones. Keep everyone outside both while the tilter runs, and load only with the table in its loading position and the frame at rest. Stop, isolate and lock out the tilter before anyone works on the load, the table or the rails, and never leave a load turned with the drive isolated unless it is mechanically supported.
适用的标准取决于目标市场。对于CE市场，EN 415-10涵盖包装机械的一般要求，而ISO 12100规定了风险评估方法，该方法规定了防护装置和紧急停止装置。
工程常见问题解答
Q: Why add a sliding table to a coil tilter? A: The table travels out from under the frame on rails, so the crane or fork-lift places the load clear of the C-frame. The table then travels back and the frame turns the load 90°.
Q: What load does the sliding-table upender take? A: Our page model is rated for 5 T, with a single-way 90° turn-over and a machine size of about L3000 × W2200 × H2600 mm.
Q: How long does the turn take? A: On the clip the turn takes about 24 s and the return about 12 s. Add table travel and loading time before comparing with your takt.
下一步
We size a sliding-table coil tilter in three steps:
- 提交您的布局图 with the load size, weight, turn angle, loading method and takt, to info@fhopepack.com.
- 48小时内收到方案, including the frame and table arrangement and the cycle check against your takt.
- 预约现场勘测 so we confirm the foundation, the table travel and the clearance around the frame.
相关阅读
- 带滑动台的翻转器和倾斜器
- Coil upender and tilter machines
- Coil tilter and upender for palletised coils
- Rotatable 180 degree multipurpose tilter
来源
- Upender specifications: Upender and tilter with sliding table product page
- 片段计时：从片段中提取的帧计时，帧之间间隔 4 秒
- 机器运行中： 我们在 YouTube 上的视频
- 标准范围： ISO 12100：2010, IN 415-10：2014
上次审核日期： 2026年10月05日
