{"id":3515,"date":"2021-01-15T05:31:36","date_gmt":"2021-01-15T05:31:36","guid":{"rendered":"https:\/\/www.fhopepack.com\/videos\/?p=3515"},"modified":"2026-10-27T15:26:59","modified_gmt":"2026-10-27T15:26:59","slug":"the-upender-and-tilter-with-rotation-table","status":"publish","type":"post","link":"https:\/\/www.fhopepack.com\/videos\/the-upender-and-tilter-with-rotation-table\/","title":{"rendered":"Mechanical Cradle Tilter &#038; 90\u00b0 Coil Upender: Engineering Guide and Kinematic Sizing"},"content":{"rendered":"<blockquote>\n<p><strong>Executive summary<\/strong>\nA mechanical cradle tilter and upender executes a controlled 90\u00b0 angular rotation for heavy industrial loads\u2014including cold-rolled steel coils, wire spools, stamping dies, and injection moulds\u2014transferring them securely between horizontal (eye-to-sky) and vertical (eye-horizontal) orientations. This technical guide reviews the motion cycle, kinematic profiling, mechanical drive design, and integration safety for cradle capacities ranging from 2,000 kg (2 t) to 40,000 kg (40 t) with a rated cycle time of 60 to 90 seconds per piece under full load.<\/p>\n<\/blockquote>\n<hr \/>\n<iframe loading=\"lazy\" width=\"940\" height=\"535\" src=\"https:\/\/www.youtube.com\/embed\/BJ8GSrAbNV8\" frameborder=\"0\" allow=\"accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share\" allowfullscreen><\/iframe>\n<h2>Table of Contents<\/h2>\n<ul>\n<li><a href=\"#kinematic-sequence-and-motion-profiling\">Kinematic Sequence and Motion Profiling<\/a><\/li>\n<li><a href=\"#cycle-time-and-velocity-analysis\">Cycle Time and Velocity Analysis<\/a><\/li>\n<li><a href=\"#mechanical-design-and-operating-principle\">Mechanical Design and Operating Principle<\/a><\/li>\n<li><a href=\"#rotating-upender-engineering-specifications\">Rotating Upender Engineering Specifications<\/a><\/li>\n<li><a href=\"#line-takt-and-throughput-calculation\">Line Takt and Throughput Calculation<\/a><\/li>\n<li><a href=\"#engineering-selection-matrix\">Engineering Selection Matrix<\/a><\/li>\n<li><a href=\"#electrical-controls-braking-and-safety-standards\">Electrical Controls, Braking, and Safety Standards<\/a><\/li>\n<li><a href=\"#engineering-faq\">Engineering FAQ<\/a><\/li>\n<li><a href=\"#rfqs-and-engineering-next-steps\">RFQs and Engineering Next Steps<\/a><\/li>\n<li><a href=\"#related-industrial-solutions\">Related Industrial Solutions<\/a><\/li>\n<li><a href=\"#reference-standards-and-sources\">Reference Standards and Sources<\/a><\/li>\n<\/ul>\n<hr \/>\n<h2>Kinematic Sequence and Motion Profiling<\/h2>\n<p>The machine kinematics employ a rigid L-shaped dual-flange platform permanently anchored to a pair of heavy-duty circular trunnion rings. This cradle assembly rides on ground, hardened alloy support rollers enclosed within a structural steel sub-base. The cradle perimeter is treated with industrial warning banding to designate the mechanical shear boundaries.<\/p>\n<p>During factory acceptance testing (FAT) without payload, the system demonstrates repeatable angular acceleration, steady-state travel, and electro-mechanical braking through two consecutive 90\u00b0 operational cycles:<\/p>\n<ol>\n<li><strong>0 to 12 s (Initial Zero State):<\/strong> The dual tilters are anchored at mechanical zero (0\u00b0 horizontal flat rest). The primary tilting deck sits flush, ready for overhead crane or forklift engagement.<\/li>\n<li><strong>16 to 28 s (Forward 90\u00b0 Kinematic Sweep):<\/strong> The left cradle engages the electromechanical drive. The curved trunnions roll along the guide wheels, transitioning the L-table smoothly through a full 90\u00b0 arc in approximately 12 seconds.<\/li>\n<li><strong>32 to 44 s (Apex Hold &amp; Position Retention):<\/strong> The machine dwells at the 90\u00b0 vertical limit switch. The spring-set, electrically released motor brake locks the cradle rigidly with zero creep under full static equilibrium.<\/li>\n<li><strong>48 to 56 s (Controlled Return Sweep):<\/strong> The gear motor reverses rotation. The cradle executes an 8-second descent to the 0\u00b0 position. The secondary unit remains isolated as a static reference.<\/li>\n<li><strong>60 to 68 s (Inter-Cycle Reset):<\/strong> Both platforms rest at mechanical bottom stops, confirming cycle reset and sensor feedback validation.<\/li>\n<li><strong>72 to 96 s (Extended Repeat Cycle):<\/strong> The drive initiates a secondary upward rotation, reaching 90\u00b0 tilt within 16 seconds, holding at apex for dwell-time monitoring and thermal verification of the brake coil.<\/li>\n<li><strong>100 to 116 s (Final Return Travel):<\/strong> The structure executes a controlled descent over 16 seconds, resetting cleanly against heavy-duty mechanical end-stops.<\/li>\n<li><strong>120 to 144 s (Standby Reset):<\/strong> Mechanical brakes lock the drive train at rest, confirming kinematic repeatability across consecutive runs.<\/li>\n<\/ol>\n<hr \/>\n<h2>Cycle Time and Velocity Analysis<\/h2>\n<p>Factory benchmarking registers the raw mechanical sweep time of the empty cradle assembly at high speed. Under actual production conditions, however, dynamic loads shift the system center of gravity (CG). The machine inverter regulates velocity via an engineered S-curve acceleration\/deceleration profile to suppress overturning moments.<\/p>\n<table>\n<thead>\n<tr>\n<th>Kinematic Stage<\/th>\n<th>Factory Timing (Unloaded)<\/th>\n<th>Production Target (Loaded)<\/th>\n<th>Functional Purpose<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><strong>First Upward Tilt (0\u00b0 \u2192 90\u00b0)<\/strong><\/td>\n<td>12 s<\/td>\n<td>25 \u2013 35 s<\/td>\n<td>Controlled torque ramp; smooth transition through 45\u00b0 CG shift.<\/td>\n<\/tr>\n<tr>\n<td><strong>Apex Dwell \/ Lock<\/strong><\/td>\n<td>12 s<\/td>\n<td>10 \u2013 15 s<\/td>\n<td>Verification of load seat, strapping access, or clamp actuation.<\/td>\n<\/tr>\n<tr>\n<td><strong>Return Tilt (90\u00b0 \u2192 0\u00b0)<\/strong><\/td>\n<td>8 s<\/td>\n<td>25 \u2013 35 s<\/td>\n<td>Counter-torque descent preventing gravitational free-fall.<\/td>\n<\/tr>\n<tr>\n<td><strong>Second Upward Tilt<\/strong><\/td>\n<td>16 s<\/td>\n<td>25 \u2013 35 s<\/td>\n<td>Secondary verification run \/ inline buffer cycle.<\/td>\n<\/tr>\n<tr>\n<td><strong>Second Return Tilt<\/strong><\/td>\n<td>16 s<\/td>\n<td>25 \u2013 35 s<\/td>\n<td>Final reset to infeed orientation.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>Note: Quoting 60 to 90 seconds per piece provides conservative takt engineering. This duration accounts for Variable Frequency Drive (VFD) regenerative braking, mechanical shock absorption at limit points, and stability checks as the payload transitions across its diagonal balance point.<\/em><\/p>\n<hr \/>\n<h2>Mechanical Design and Operating Principle<\/h2>\n<p>Unlike scissor-lift tilters or hydraulic-ram upenders, a <strong>mechanical cradle tilter<\/strong> rotates entirely through a rolling radial sector. The product rests continuously against two mutually perpendicular faces of the rigid L-frame.<\/p>\n<pre><code>       [Open Loading Face]\n               |\n               v\n         +------------+\n         | Payload    |\n         | (Coil\/Die) |\n    +----+------------+\n    |    |  &lt;-- 90&deg; Radial Roll Center\n    | L-Table         \\\n    +-------------------\\____ (Curved Trunnion Rings)\n    =========================== (Hardened Base Support Rollers)\n         [Heavy Rigid Sub-Base]<\/code><\/pre>\n<p>As the heavy-duty drive turns the circular cradle via double roller chains or heavy pinions, the contact footprint rolls smoothly across the base support rollers. Gravity forces vector entirely downward through the machine chassis into the plant floor, avoiding the high localized cantilever stress typical of pivot-pin hinge systems.<\/p>\n<h3>Core Component Breakdown<\/h3>\n<table>\n<thead>\n<tr>\n<th>Sub-Assembly<\/th>\n<th>Engineering Construction<\/th>\n<th>Operational Function<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><strong>L-Shaped Table<\/strong><\/td>\n<td>High-tensile structural channel &amp; plate<\/td>\n<td>Direct support of load across base and back faces; rigid 90\u00b0 geometry.<\/td>\n<\/tr>\n<tr>\n<td><strong>Curved Cradle Trunnion<\/strong><\/td>\n<td>Machined radial circular segments<\/td>\n<td>Converts rotational motor torque into smooth rolling 90\u00b0 motion.<\/td>\n<\/tr>\n<tr>\n<td><strong>Rigid Machine Sub-Base<\/strong><\/td>\n<td>Welded heavy H-beam structure<\/td>\n<td>Houses double support trunnion rollers; anchors unit to shop floor.<\/td>\n<\/tr>\n<tr>\n<td><strong>Drive &amp; Brake Assembly<\/strong><\/td>\n<td>High-reduction helical-bevel gear motor<\/td>\n<td>Direct electromechanical drive with fail-safe disk brake (zero hydraulic leak risk).<\/td>\n<\/tr>\n<tr>\n<td><strong>Shear-Zone Markings<\/strong><\/td>\n<td>Class 1 high-visibility hazard striping<\/td>\n<td>Defines visual exclusion zone around dynamic rolling cradle edges.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Platforms are configured with flat wear-resistant plates (for heavy stamping tools and dies) or 120\u00b0 V-saddles lined with high-density polyurethane (to cradle steel\/copper coils without gouging or edge distortion).<\/p>\n<hr \/>\n<h2>Rotating Upender Engineering Specifications<\/h2>\n<p>The standardized heavy-duty mechanical cradle platform covers capacities from 2 t to 40 t:<\/p>\n<table>\n<thead>\n<tr>\n<th>Technical Parameter<\/th>\n<th>Standard Heavy-Duty Specification<\/th>\n<th>Custom Engineered Range<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td><strong>Maximum Load Capacity<\/strong><\/td>\n<td>2,000 kg \u2013 40,000 kg (2 t \u2013 40 t)<\/td>\n<td>Up to 60 t on engineered request<\/td>\n<\/tr>\n<tr>\n<td><strong>Payload Geometries<\/strong><\/td>\n<td>Slit coils, master coils, stamping tools, moulds<\/td>\n<td>Wire drums, paper rolls, cast ingots<\/td>\n<\/tr>\n<tr>\n<td><strong>Flat Table Dimensions<\/strong><\/td>\n<td>1,500 \u00d7 1,500 mm<\/td>\n<td>1,000 \u00d7 1,000 mm up to 3,000 \u00d7 3,000 mm<\/td>\n<\/tr>\n<tr>\n<td><strong>V-Saddle Table Dimensions<\/strong><\/td>\n<td>1,500 \u00d7 1,500 mm (Polyurethane lined)<\/td>\n<td>Sized to coil outer diameter (OD)<\/td>\n<\/tr>\n<tr>\n<td><strong>Tilting Angle &amp; Precision<\/strong><\/td>\n<td>90\u00b0 (\u00b1 0.5\u00b0 electromechanical limit control)<\/td>\n<td>Exact horizontal-to-vertical alignment<\/td>\n<\/tr>\n<tr>\n<td><strong>Total Tilt Duration<\/strong><\/td>\n<td>60 \u2013 90 s (Payload dependent)<\/td>\n<td>40 s (Light series) to 120 s (Heavy 40 t)<\/td>\n<\/tr>\n<tr>\n<td><strong>Main Drive Power Rating<\/strong><\/td>\n<td>4.0 kW, 5.5 kW, 7.5 kW, or 15.0 kW<\/td>\n<td>Sized by full torsional inertia calculation<\/td>\n<\/tr>\n<tr>\n<td><strong>Electrical Supply Standard<\/strong><\/td>\n<td>380 V \u2013 480 V, 50\/60 Hz, 3-Phase<\/td>\n<td>Globally compatible industrial inputs<\/td>\n<\/tr>\n<tr>\n<td><strong>Drive System Mechanism<\/strong><\/td>\n<td>Multi-strand heavy chain \/ Precision pinion-gear<\/td>\n<td>Fail-safe electromechanical self-locking<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<hr \/>\n<h2>Line Takt and Throughput Calculation<\/h2>\n<p>To integrate a 90\u00b0 tilter into a continuous packaging or press line, cycle limits must be balanced against handling times.<\/p>\n<ul>\n<li><strong>Target Throughput:<\/strong> 30 loads\/hour<\/li>\n<li><strong>Available Gross Takt Time:<\/strong> <code>T_takt = 3,600 s &divide; 30 = 120 s\/cycle<\/code><\/li>\n<li><strong>Machine Motion Budget:<\/strong> <code>T_tilt = 60 s to 90 s<\/code><\/li>\n<li><strong>Net Material Handling Window:<\/strong> <code>T_handling = T_takt - T_tilt = 30 s to 60 s<\/code><\/li>\n<\/ul>\n<pre><code>Total Line Takt: 120 s (30 Loads\/Hour)\n|------------------ Machine Motion: 60 - 90 s ------------------|-- Handling: 30 - 60 s --|\n[ Load &amp; Secure ] -&gt; [ 90&deg; Controlled Tilt ] -&gt; [ Limit Dwell ] -&gt; [ Crane \/ Fork Removal ]<\/code><\/pre>\n<h3>Critical Flow Constraint<\/h3>\n<p>A 30-to-60-second window is sufficient for forklift transfer, but can create bottlenecks when relying on an overhead crane with manual C-hook rigging. When line balance requires tighter integration, the table surfaces are fitted with integrated motorized roller conveyors or chain transfers. This allows palletized coils to index into and out of the tilting cradle automatically without overhead crane wait times.<\/p>\n<hr \/>\n<h2>Engineering Selection Matrix<\/h2>\n<p>Review these operational checkpoints before freezing the equipment specification:<\/p>\n<ul>\n<li><strong>Load Geometry &amp; Envelope:<\/strong> Confirm maximum width, outside diameter (OD), inside diameter (ID), and payload mass against the 2,000 kg to 40,000 kg envelope.<\/li>\n<li><strong>Deck Configuration:<\/strong> Select a heavy plate flat deck (flat dies, bundled packs) or a 120\u00b0 V-cradle with protective polyurethane\/hardwood facing (bare coils).<\/li>\n<li><strong>Motion Profile:<\/strong> Confirm duty cycle: 0\u00b0 to 90\u00b0 (upending), 90\u00b0 to 0\u00b0 (downending), or continuous bidirectional duty.<\/li>\n<li><strong>Transfer Method:<\/strong> Determine loading method: overhead crane (requires open top clearance), counterbalanced forklift, or automated roller\/chain conveyor.<\/li>\n<li><strong>Thermal &amp; Drive Margins:<\/strong> Verify motor kilowatt rating and continuous holding capacity for operations exceeding 20 cycles per hour.<\/li>\n<\/ul>\n<hr \/>\n<h2>Electrical Controls, Braking, and Safety Standards<\/h2>\n<p>A cradle tilter repositions heavy industrial masses through a wide radial volume. As the curved cradle swings, the mechanical shear point between the trunnion sector and the sub-base closes continuously.<\/p>\n<pre><code>+---------------------------------------------------------+\n|                  PERIMETER SAFETY ZONE                  |\n|                                                         |\n|   +-------------------+         [Physical Perimeter]    |\n|   |  Optical Light    |=======&gt; [Hard Mesh Guarding]    |\n|   |  Curtains         |         [Interlocked Access]    |\n|   +-------------------+                                 |\n|             \\                                           |\n|              v                                          |\n|        [ Tilter Frame ] &lt;== [ Dual Limit Switches ]     |\n|        [ Heavy Cradle ] &lt;== [ Spring-Set Brake ]        |\n|                                                         |\n+---------------------------------------------------------+<\/code><\/pre>\n<h3>Safety Integration Architecture<\/h3>\n<ol>\n<li><strong>Mechanical Restraint &amp; Drive Lock:<\/strong> The electromechanical drive utilizes a heavy-duty spring-set, electrically released dynamic brake. In the event of a sudden plant power loss, the brake engages automatically, arresting the loaded cradle securely at any angle along its 90\u00b0 path without fluid bypass risks.<\/li>\n<li><strong>Perimeter Enclosure:<\/strong> Personnel must be protected from the dynamic sweep zone. In accordance with safety standards, production cells require 2,000 mm high physical perimeter wire-mesh fencing, dual-channel interlocked access gates, and optical light curtains across the loading face.<\/li>\n<li><strong>Lockout\/Tagout (LOTO):<\/strong> Complete zero-energy state isolation (electrical and mechanical) is required prior to maintenance. Mechanically locked maintenance safety pins must be inserted into the cradle chassis before technicians access the internal roller beds.<\/li>\n<li><strong>Governing Design Standards:<\/strong>\n<ul>\n<li><strong>ISO 12100:2010:<\/strong> Safety of machinery \u2014 General principles for design, risk assessment, and risk reduction.<\/li>\n<li><strong>EN 415-10:2014:<\/strong> Safety of packaging machines \u2014 General requirements for integrated modular machinery.<\/li>\n<li><strong>OSHA 29 CFR 1910.147:<\/strong> Control of Hazardous Energy (Lockout\/Tagout).<\/li>\n<\/ul><\/li>\n<\/ol>\n<hr \/>\n<h2>Engineering FAQ<\/h2>\n<p><strong>Q: What are the main benefits of a mechanical cradle tilter over hydraulic upenders?<\/strong>\nA: Mechanical cradle upenders eliminate hydraulic power units (HPUs), oil leaks, proportional valve maintenance, and cylinder seal degradation. The mechanical trunnion design transfers load weights directly through radial rollers into the base frame, keeping energy use low and locking securely in any position via an electromechanical brake.<\/p>\n<p><strong>Q: Why does a loaded cycle take 60 to 90 seconds while an empty cycle takes only 12 to 16 seconds?<\/strong>\nA: The unloaded cycle demonstrates baseline motor and drivetrain velocity. Under load, high-inertia workpieces require conservative S-curve acceleration and deceleration profiles via a Variable Frequency Drive (VFD). This prevents the load&#8217;s center of gravity from generating shock loads on the drivetrain as it passes the 45\u00b0 balance point.<\/p>\n<p><strong>Q: Can the upender handle loads with varying outer diameters on the same platform?<\/strong>\nA: Yes. When equipped with a centered 120\u00b0 V-saddle, the platform naturally centers varying coil diameters along the primary rotation axis, preventing lateral roll during the 90\u00b0 motion.<\/p>\n<hr \/>\n<h2>RFQs and Engineering Next Steps<\/h2>\n<p>We engineer and supply standard and custom-built cradle tilters tailored to your specific plant layout:<\/p>\n<ol>\n<li><strong>Submit Facility Parameters:<\/strong> Send your product dimensions, maximum weight, current material handling method, and factory layout drawings to <strong>info@fhopepack.com<\/strong>.<\/li>\n<li><strong>Receive 48-Hour Technical Proposal:<\/strong> Our mechanical team provides a general assembly drawing, drive capacity calculation, and detailed cycle-time simulation within 48 hours.<\/li>\n<li><strong>Pre-Commissioning Review:<\/strong> We verify floor loading capacities, dynamic ground anchoring, crane overhead hook clearances, and perimeter safety zones prior to production release.<\/li>\n<\/ol>\n<hr \/>\n<h2>Related Industrial Solutions<\/h2>\n<ul>\n<li><a href=\"https:\/\/www.fhopepack.com\/Mechanical\/Rotating-Coil-Upender.html\">Rotating Heavy Coil Upender Series<\/a><\/li>\n<li><a href=\"https:\/\/www.fhopepack.com\/Mechanical\/up-ender.html\">Industrial Upender and Tilter with Powered Sliding Table<\/a><\/li>\n<li><a href=\"https:\/\/www.fhopepack.com\/Coil_upender.html\">Comprehensive Coil Tilter &amp; Downender Engineering Range<\/a><\/li>\n<li><a href=\"https:\/\/www.fhopepack.com\/videos\/practical-well-designed-coil-tilter-and-coil-upender\/\">Automated 90\u00b0 Palletized Coil Turnstation Systems<\/a><\/li>\n<\/ul>\n<hr \/>\n<h2>Reference Standards and Sources<\/h2>\n<ul>\n<li>Mechanical Specifications &amp; Turnstation Dimensions: <a href=\"https:\/\/www.fhopepack.com\/Mechanical\/Rotating-Coil-Upender.html\">FHOPE Industrial Coil Upender Portal<\/a><\/li>\n<li>Machine Safety Design Scope: <a href=\"https:\/\/www.nen.nl\/en\/nen-en-415-10-2014-en-191845\">EN 415-10:2014 Safety Requirements for Packaging Systems<\/a><\/li>\n<li>Plant Equipment Risk Assessment Protocol: <a href=\"https:\/\/www.iso.org\/standard\/51528.html\">ISO 12100:2010 Safety of Machinery<\/a><\/li>\n<\/ul>\n<p><em>Last engineering review: October 2026<\/em><\/p>","protected":false},"excerpt":{"rendered":"<p>Executive summary A mechanical cradle tilter and upender executes a controlled 90\u00b0 angular rotation for heavy industrial loads\u2014including cold-rolled steel coils, wire spools, stamping dies, and injection moulds\u2014transferring them securely between horizontal (eye-to-sky) and vertical [&hellip;]<\/p>","protected":false},"author":1,"featured_media":3516,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_seopress_titles_title":"Tilter and upender with rotation table: 90 degree turn","_seopress_titles_desc":"How our tilter and upender with rotation table turns loads 90 degrees on a cradle, with clip timing, specs, a takt check, a checklist and safety notes.","_seopress_robots_index":"","_seopress_robots_follow":"","_seopress_robots_imageindex":"","_seopress_robots_snippet":"","_seopress_robots_primary_cat":"none","_seopress_robots_breadcrumbs":"","_seopress_robots_freeze_modified_date":"","_seopress_robots_custom_modified_date":"","_seopress_robots_canonical":"","_seopress_social_fb_title":"","_seopress_social_fb_desc":"","_seopress_social_fb_img":"","_seopress_social_fb_img_attachment_id":0,"_seopress_social_fb_img_width":0,"_seopress_social_fb_img_height":0,"_seopress_social_twitter_title":"","_seopress_social_twitter_desc":"","_seopress_social_twitter_img":"","_seopress_social_twitter_img_attachment_id":0,"_seopress_social_twitter_img_width":0,"_seopress_social_twitter_img_height":0,"_seopress_redirections_value":"","_seopress_redirections_enabled":"","_seopress_redirections_enabled_regex":"","_seopress_redirections_logged_status":"both","_seopress_redirections_param":"","_seopress_redirections_type":301,"_seopress_analysis_target_kw":"","_seopress_news_disabled":"","_seopress_video_disabled":"","_seopress_video":[],"_seopress_pro_schemas_manual":[{"_seopress_pro_rich_snippets_type":"custom","_seopress_pro_rich_snippets_custom":"<script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@graph\": [{\"@type\": \"FAQPage\", \"@id\": \"https:\/\/www.fhopepack.com\/videos\/the-upender-and-tilter-with-rotation-table\/#faq\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"How heavy a load can the rotating upender turn?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"From 2,000 kg up to 40 t, depending on the size.\"}}, {\"@type\": \"Question\", \"name\": \"How long does one 90 degree turn take?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Our upender is quoted at 60 to 90 s per piece under load. The empty turn on the clip takes about 12 to 16 s.\"}}, {\"@type\": \"Question\", \"name\": \"Which table types are available?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"A flat table or a V table, each 1,500 by 1,500 mm as standard and customised to the load.\"}}]}, {\"@type\": \"VideoObject\", \"@id\": \"https:\/\/www.fhopepack.com\/videos\/the-upender-and-tilter-with-rotation-table\/#video\", \"name\": \"Tilter and Upender with Rotation Table: 90 Degree Turn on a Cradle\", \"description\": \"A tilter and upender with a rotation table turns a heavy load such as a coil or a mould through 90 degrees, from lying to standing or back. Our clip, about 144 s long, shows two yellow cradle tilters on blue bases; the left one runs through two full tilt cycles empty.\", \"thumbnailUrl\": [\"https:\/\/i.ytimg.com\/vi\/BJ8GSrAbNV8\/hqdefault.jpg\"], \"embedUrl\": \"https:\/\/www.youtube.com\/embed\/BJ8GSrAbNV8\", \"contentUrl\": \"https:\/\/www.youtube.com\/watch?v=BJ8GSrAbNV8\", \"uploadDate\": \"2021-01-15\", \"duration\": \"PT2M23S\"}]}<\/script>"}],"_seopress_pro_rich_snippets_disable_all":"","_seopress_pro_rich_snippets_disable":{"4494":"1"},"_seopress_pro_schemas":[],"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"default","adv-header-id-meta":"","stick-header-meta":"default","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"fifu_image_url":"","fifu_image_alt":"","footnotes":""},"categories":[194],"tags":[191,192],"class_list":["post-3515","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-tilterupender","tag-tilter","tag-upender"],"_links":{"self":[{"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/posts\/3515","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/comments?post=3515"}],"version-history":[{"count":8,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/posts\/3515\/revisions"}],"predecessor-version":[{"id":17881,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/posts\/3515\/revisions\/17881"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/media\/3516"}],"wp:attachment":[{"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/media?parent=3515"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/categories?post=3515"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.fhopepack.com\/videos\/wp-json\/wp\/v2\/tags?post=3515"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}