mașină de bobinat țevi și mașină de bobinat țevi

Rezumat

An automatic pipe winding machine (pipe coiler) takes continuous flexible PE, PEX, PE-RT, or PVC tube directly from the extrusion haul-off and winds it into tightly layered, dimensioned coils ready for immediate strapping and film wrapping. A precision encoder-based meter counter tracks length in real time, servo-driven rotary formers synchronize with line speed via dynamic torque control, and pneumatic clamping plates collapse to discharge the finished bundle. The FCL-800 series processes tube outside diameters (OD) of 5–30 mm into coils up to 800 mm OD at line speeds reaching 80 m/min, while the heavy-duty FCL400 accommodates large-format coils spanning 680–1,200 mm OD. Below: operational mechanics, standardized sizing specifications, cycle time calculations, downstream packaging, and EN/ISO safety compliance.

Cuprins

Ce face o mașină de înfășurat țevi

Continuous extrusion lines discharge flexible polymer pipe non-stop. Manual coiling on manual reels creates loose turns, irregular outer dimensions, inconsistent tension that deforms semi-hot pipes, and hazardous coil-spring risks.

An industrial pipe winding machine automates three core processes:

  1. Tension-Controlled Rotary Winding: Regulates take-up torque to maintain uniform tension without thinning or ovalizing warm extrusions.
  2. Servo Layer Traversal: Drives a linear guide synchronized to former rotation, laying uniform, pitch-perfect wraps across the spool width.
  3. Dimensional Containment & Unloading: Forms tight inner diameters (ID) and precise coil widths under adjustable side-plate clamping, collapsing core segments automatically for clean discharge.

Typical materials include PE-80 / PE-100 agricultural irrigation and potable water pipes, PEX and PE-RT multi-layer floor heating pipes, reinforced PVC braided hoses, and precision nylon/polyurethane tubing.

Cum funcționează ciclul de înfășurare

The automatic coiling cycle integrates with upstream haul-offs through five coordinated steps:

  1. Feed & Clamping: The pipe leading end enters through the guide eyelet and locks into the pneumatic core clamp. Adjustable spool plates set the target coil inner diameter (ID) and reel traverse width.
  2. Synchronized Winding: The former rotates while an electronic traverse guide shifts back and forth by exactly one tube OD per revolution. As coil diameter builds from ID to final OD, the variable-frequency or servo drive progressively reduces spindle RPM (v_line = ω × r) to maintain steady linear take-up speed matching the extruder.
  3. Length Metering & Cut: A twin-wheel tracking encoder measures continuous running length. Upon reaching the target value (e.g., 100.0 m ± 0.2%), the pneumatic shear or rotary flying blade executes an instantaneous square cut.
  4. Integrated Strapping & Retention: Retractable strap chutes route polypropylene (PP) or polyester (PET) bands through the coil core. Tensioners strap the bundle at 2 to 4 points while clamping arms hold outer coils from unspringing.
  5. Colaps și descărcare a miezului: The inner former segments collapse radially inward, outer clamping flanges retract, and the ejector kicks the coil onto an accumulation roller conveyor.

A main control panel houses the PLC and industrial HMI, tracking production metrics, recipe presets, and servo alarms via industrial Ethernet. Mechanical safety interlocks and wire-mesh guards isolate all rotating formers.

Alegerea unui model

Selecting the correct coiler configuration depends on outer pipe diameter, required coil pack weight, and maximum extrusion output:

Model Interval diametru exterior țeavă Interval ID bobină Max bobină OD Coil Width (Traverse) Viteză maximă a liniei
FCL-800A 5 – 16 mm 200 – 300 mm 500 – 800 mm 80 – 200 mm Până la 80 m/min
FCL-800B 10 – 20 mm 250 – 500 mm 800 mm 100 – 300 mm Până la 80 m/min
FCL-800C 15 – 30 mm 300 – 600 mm 800 mm 120 – 350 mm Până la 60 m/min
FCL-400 16 – 40 mm 300 – 500 mm 680 – 1,200 mm 150 – 400 mm Până la 50 m/min

Parametri de funcționare: 0.6–0.7 MPa pneumatic supply; 380–480 V, 3-phase, 50/60 Hz; strapping strap weld efficiency ≥ 85%; machine availability ≥ 98.5%.

Exemplu de dimensionare: o bobină de 100 m

Scenariul aplicației: Solid-wall 16 mm OD PE irrigation pipe, extruded at a continuous haul-off rate of 60 m/min, packaged into 100 m coils on an FCL-800B with a 400 mm core ID and 200 mm coil width.

Pasul de verificare Calcul ingineresc Cycle Value
Compatibilitate dimensională Tube OD = 16 mm (within 10–20 mm); Length = 100 m Complet compatibil
Turns per Traverse Layer 200 mm width ÷ 16 mm OD = 12.5 12 turns/layer (nominal)
Pure Winding Time (t_w) 100 m ÷ 60 m/min 1.67 min (100 s)
Coil Changeover Overhead (t_c) Cut, 3× strap cycle, core collapse, eject 25–35 s (single-station baseline)
Total Cycle Time per Coil t_total = t_w + t_c 125–135 s
Effective Single-Station Output 3,600 s ÷ 130 s ≈ 27.6 coils/hour
Coiler Speed Safety Margin 80 m/min max capacity vs 60 m/min extrusion +33% surplus drive headroom

Analiza de inginerie: Continuous extrusion cannot halt during the 25–35 s strapping and ejection sequence (t_c). Two engineering configurations maintain non-stop production:

  1. Vertical Accumulator (Dancer Tower): Stores 25–35 m of extruded pipe under counterbalanced tension while the single-spindle coiler unloads, then winds at 75–80 m/min to empty the accumulator.
  2. Dual-Station Automatic Coiler: Features twin winding formers on an indexing turntable. As station A stops for cutting and strapping, pipe transfer guides automatically deflect the live stream to station B with zero line slowdown, achieving up to 40–45 coils/hour continuous throughput.

După înfășurare: legare cu banda, înfășurare, contracție

A wound coil must retain its structural geometry throughout warehousing, shipping, and retail dispensing:

  • Legare radială: High-tensile PP or PET straps (9–12 mm width) seal directly around the bundle cross-section. Standard cycles apply 2, 3, or 4 radial ties with hot-melt heat sealing or friction-weld joints.
  • Through-Eye Stretch Wrapping: Orbital film wrappers pass linear stretch film (LLDPE) directly through the open center core (“eye”) of the coil while rotating it on support rollers. This provides 100% dustproof and moisture-tight encapsulation against surface scuffing.
  • Thermal Shrink Packaging: Coils slide into PE/polyolefin film pockets and pass through an infrared hot-air shrink tunnel, yielding a skin-tight, tamper-evident retail package with optimal brand label visibility.

Both horizontal-axis and vertical-axis layouts integrate modularly with in-line robotic palletizing cells.

Listă de verificare a selecției

Verify these five mechanical and production boundaries prior to equipment quotation:

  1. Pipe Material & Wall Thickness: Flexural modulus and minimum cold bend radius (e.g., standard SDR ratios for HDPE vs ultra-flexible PVC hose).
  2. Reel Dimensions: Required core ID, maximum package OD, and face traverse width.
  3. Extrusion Line Speed: Nominal and maximum haul-off velocity (m/min) to determine single vs dual-station machine architecture.
  4. Finisare secundară: Strapping count, stretch wrap overlap percentage (typically 30–50%), or complete shrink film bagging.
  5. Integrarea liniei: Extruder interface protocol (digital dry contacts, Profinet, or Ethernet/IP) for automatic line-speed tracking and emergency stop (E-stop) interlock.

Siguranță: EN 415-10 și ISO 12100

High-speed coiling machinery features significant rotational inertia, traversing pinch points, and active cutting tooling. All units comply with international packaging machinery safety requirements:

  • ISO 12100: 2010: Comprehensive risk assessment addressing residual pinch-point mechanical hazards, pneumatic failure scenarios, and electrical safety.
  • Conformitate EN 415-10: Fixed perimeter sheet metal and welded wire-mesh barriers guard rotating spools, collapsing heads, and strapping arms.
  • Interlocking & LOTO: Access doors incorporate dual-channel Category 3 / Performance Level d (PL d) safety switches (EN ISO 13849-1). Opening any interlock immediately drops actuator air pressure and engages fail-safe servo motor brakes.
  • Blade Isolation: Pneumatic shear mechanisms operate within enclosed channels, protected by mechanical drop-stops during manual changeovers.

Întrebări frecvente despre inginerie

Q: Can the coiler handle line acceleration during extruder startup? A: Yes. The master PLC monitors linear haul-off line speed via encoder or 0–10 V / 4–20 mA analog input. The coiler spindle servo continuously matches speed using closed-loop torque and velocity control, preventing tube stretching during startup and ramping.

Q: What maintains length-count accuracy across varying line speeds? A: Meter counting uses twin precision measuring wheels with high-friction polyurethane running rings mounted on pneumatic float arms. Coupled with high-resolution incremental rotary encoders, accuracy reaches ± 0.2% on rigid PE and ± 0.5% on flexible PVC.

Q: What coil limits require stepping up from FCL-800 to FCL-400? A: The FCL-800 series is optimized for high-speed small-to-medium coils (up to 800 mm OD, 30 mm pipe OD). When coil OD exceeds 800 mm (up to 1,200 mm) or pipe diameter reaches 32–40 mm, the higher winding torque, widened strap track, and heavy-duty frame of the FCL-400 become mandatory.

Q: Can the coiling unit function as an independent off-line rewinder? A: Yes. An optional driven decoiler and motorized tension-relief stand allow the coiler to convert bulk master coils or loose loops into small, tied retail lengths offline.

Urmatorul pas

To size an optimal coiler configuration and receive engineering layout drawings:

  1. Provide Pipe Data: Pipe OD, wall thickness, material grade, coil ID/OD targets, and extrusion line speed.
  2. Select Packaging Mode: Strapping only (number of ties), orbital through-eye stretch wrapping, or shrink packaging.
  3. Contact Engineering: Email specifications to info@fhopepack.com. Our engineering team returns a customized system specification sheet and preliminary dimensional CAD layout within 24 hours.

Surse

  • FHOPE Packaging Machinery: FCL-800 High-Speed Tube Coiling & Strapping Technical Documentation.
  • FHOPE Engineering Project Archive: Large-Diameter Spool Application Files (FCL-400 Series).
  • International Standard EN 415-10: Safety of packaging machines – General requirements.
  • Standardul internațional ISO 12100:2010: Siguranța mașinilor. Principii generale pentru proiectare. Evaluarea riscurilor și reducerea riscurilor.
  • International Standard EN ISO 13849-1: Siguranța mașinilor – Părțile sistemelor de control legate de siguranță.

Ultima recenzie: 21.09.2026

postări asemănatoare

Rezervați un apel
Rezervați un apel