Samenvatting
Heavy coils and molds must change between horizontal and vertical, and manual or crane-based flips put the crew and the load at risk. This upender and tilter rotates a large coil from lying flat to standing upright on a controlled tilting arm, with the operator clear of the load path at a separate control cabinet. We build upenders and tilters for coil and mold loads. Load range and rotation are confirmed per project.
Inhoudsopgave
- Why coils and molds need controlled rotation
- Wat de machine doet
- The tilting cycle
- From horizontal to vertical
- Coil and mold loads
- Wat de beelden laten zien
- Typische configuratie
- Selectie checklist
- Bediening en veiligheid
- Veelgestelde vragen over techniek
- Volgende stap
- Gerelateerd lezen
- Bronnen en standaarden
Why coils and molds need controlled rotation
A heavy coil or mold that must stand upright is usually flipped by crane and slings, which swings the load and risks the crew and the product edge together. A controlled rotation moves the load deliberately on a machine instead. The upender takes the load from one orientation to the other under power, so nothing hangs from a hook while people reposition it. The load range and its handling are confirmed per project.
Wat de machine doet
The machine is an upender and tilter for coil and mold loads. A curved tilting arm raises the load from the base and rotates it to the new orientation, holding it there for the next step. The operator runs the cycle from a separate control cabinet, out of the rotation zone. Rotation is hydraulic or mechanical per project, and the load is confirmed per project.
The tilting cycle
The footage shows one full tilt. The coil starts horizontal on the upender, the arm lifts and rotates it partway, then completes the travel to vertical, where it is held stable. The whole change happens on the machine without the operator touching the load. The rotation is smooth and controlled from start to finish. Cycle parameters are confirmed per project.
From horizontal to vertical
The demonstration moves the load through the change an upender exists to make: eye-horizontal on the floor, eye-vertical for the next process. Because the arm supports the load through the swing, the coil keeps its shape instead of being dragged or dropped. The final orientation is presented ready for unwinding, mould changing or transport as required. The orientation change is confirmed per project.
Coil and mold loads
This class of upender is marketed for both coils and molds. The clip rotates a large metal coil, standing it upright under the arm. Mold handling uses the same controlled rotation principle, with table and clamping style selected for the mold. What the footage proves is the mechanical rotation of a heavy rounded load. Mold configuration is confirmed per project.
Wat de beelden laten zien
Our footage shows a heavy upender rotating a large coil from horizontal to vertical. It is a general demonstration, so your load range and rotation needs are confirmed with us per project.
Typische configuratie
De onderstaande cijfers geven de functionele ontwerpgrenzen weer in plaats van numerieke waarden en zijn per project bevestigd.
| Parameter | Typisch bereik, bevestigd per project. |
|---|---|
| massa | coils, molds |
| Beweging | controlled tilt |
| Drive | hydraulic or mechanical |
| Werking | remote control cabinet |
| het merken | hazard striping, guarding area |
| Elektrische voeding | 380 V driefase 50 Hz, of 220 V eenfase voor lichte machines, te kiezen per project. |
Selectie checklist
| Vraag | Bevestig per project |
|---|---|
| Laadbereik | coil widths, mold sizes, weights |
| Rotatie | tilt angle, holding position |
| Drive | hydraulic or mechanical capacity |
| Werking | control cabinet, clear load path |
| Veiligheid | guards, emergency stop, zone marking |
| Elektrische voeding | spanning, fase en frequentie op locatie |
Bediening en veiligheid
Run the cycle from the control cabinet and the machine raises and rotates the load automatically. Keep clear of the tilting arm, load path and retaining area while the machine runs, with guarding and emergency stops at the operator position. Routine checks cover the drive, arm, holding mechanisms, sensors and control, per the machine manual. Confirm the rotation against the load before each run so loads tilt without damage.
Veelgestelde vragen over techniek
Q: What does this upender do? A: It rotates a heavy coil or mold between horizontal and vertical on a tilting arm.
Q: Why not crane flip? A: A crane swing puts the crew and the product edge at risk; the machine moves the load under control.
Q: Does the operator touch the load? A: No, the run is controlled from a separate cabinet, out of the rotation zone.
Q: What loads does it handle? A: Coils and molds, with configuration confirmed per project.
Q: What does the footage prove? A: A mechanical tilt of a large coil from horizontal to vertical in one smooth cycle.
Volgende stap
- Email us at info@fhopepack.com with your load range and rotation needs.
- Binnen 48 uur sturen we u een voorstel voor de ombouw en een plattegrondtekening.
- We arrange a site survey to confirm load range and orientation needs.
Gerelateerd lezen
- Overzicht van apparatuur voor het omkeren van coils
- Hydraulische kantel- en hefinrichting
- Upender machine
- FHOPE verpakkingsmachine productlijnen
Bronnen en standaarden
- ISO 12100:2010 Veiligheid van machines, algemene principes voor ontwerp en risicobeoordeling
- EN 415-10:2014 Veiligheid van verpakkingsmachines, algemene eisen
- EN ISO 13849-1:2023 Veiligheid van machines, veiligheidsgerelateerde onderdelen van besturingssystemen
FHOPE top quality upender and tilter demonstration video. Reviewed as a general demonstration; load range confirmed per project.
Laatst beoordeeld: 11-10-2026
