Samenvatting
PE film is the standard overwrap for steel, copper and wire coils, and how it is applied decides whether the coil stays covered. This article examines PE film application in vertical coil wrapping machines: film passes lay the cover around the coil, holding it against corrosion and handling. We build vertical coil wrapping machines for PE film. Coil range and wrap plan are confirmed per project.
Inhoudsopgave
- Why PE film for coils
- Wat de machine doet
- PE film application
- Vertical coil wrapping
- Steel copper and wire coils
- Film tension and cover
- Typische configuratie
- Wat de video laat zien
- Selectie checklist
- Bediening en veiligheid
- Veelgestelde vragen over techniek
- Volgende stap
- Gerelateerd lezen
- Bronnen en standaarden
Why PE film for coils
Polyethylene film is the workhorse overwrap for coils because it covers, holds and breathes the way coils need, and it suits steel, copper and wire alike. The film’s job is to keep moisture and dirt off the steel and hold the layers together in transit. PE film works only as well as its application, which is what the machine controls. The coil range and film plan are confirmed per project.
Wat de machine doet
The vertical coil wrapping machine applies PE film around the coil, laying the cover that protects and holds the wound material. Coils are wrapped by the machine in a set sequence, so the film reaches around the same way on every coil. Because the film tension and passes are machine-set, PE film works to its full effect rather than by hand. The covered steps and wrap plan are confirmed per project.
PE film application
PE film is drawn from the roll and applied around the coil in controlled passes, tightening the cover as it builds. Application is where film succeeds or fails: tension too loose leaves the coil exposed, and a machine-held application keeps it even. The film is held at the set tension across the full pass of the coil. The film grade and tension follow the coil, confirmed per project.
Vertical coil wrapping
In the vertical configuration the coil is wrapped on its axis, with the film passes laid across the coil’s width. Vertical wrapping suits coils that present their flat face to the wrapper, covering the faces and the outer diameter. The machine keeps the coil stationary while wrapping on the vertical plane. Vertical wrap settings follow the coil’s dimensions, confirmed per project.
Steel copper and wire coils
The machine wraps the range of material coils that need PE film protection: steel, copper and wire coils. These coils share the need for a cover that holds without marking, and PE film applied evenly meets it. The material range is confirmed per project against the coils actually run. One machine covers the coil mix the facility packs.
Film tension and cover
Holding film tension on the machine is what makes the cover consistent, and even cover is what protects the coil through handling and transit. Cover means the film reaches the areas that matter, faces, diameter and edges. Machine-set tension and passes remove the operator’s variability from the wrap. Tension and cover requirements are confirmed per project against the coil mix.
Typische configuratie
De onderstaande cijfers geven de functionele ontwerpgrenzen weer in plaats van numerieke waarden en zijn per project bevestigd.
| Parameter | Typisch bereik, bevestigd per project. |
|---|---|
| Spoel | steel, copper, wire |
| Film | PE-niveau |
| Wikkel | verticale passen |
| Spanning | zet standaard |
| uitgang | bedieningsafstelling |
| Elektrische voeding | 380 V driefase 50 Hz, of 220 V eenfase voor lichte machines, te kiezen per project. |
Wat de video laat zien
Our footage shows a vertical coil wrapping machine applying PE film. It is a general demonstration, so your coil range and wrap plan are confirmed with us per project.
Selectie checklist
| Vraag | Bevestig per project |
|---|---|
| Spoelbereik | sizes, materials |
| Film | PE-niveau |
| Wikkel | vertical plan |
| Spanning | zet standaard |
| uitgang | bedieningsafstelling |
| Elektrische voeding | spanning, fase en frequentie op locatie |
Bediening en veiligheid
Run the recipe from the panel and the machine wraps each coil with PE film automatically. Keep clear of the wrap ring, film path, tension system and outfeed while the machine runs, with guarding and emergency stops at the operator position. Routine checks cover the ring, film carriage, tension elements, sensors and control, per the machine manual. Confirm the film settings against the coil before each run so wraps stay even.
Veelgestelde vragen over techniek
Q: Why PE film for coils? A: PE covers and holds coils well and protects steel, copper and wire alike.
Q: What makes PE film work? A: Machine-held tension and even passes, not the pull of a hand wrap.
Q: How does vertical wrapping work? A: The coil is wrapped on its axis with film passes across its width.
Q: What coils does it take? A: Steel, copper and wire coils, confirmed per project.
Q: What does even cover protect? A: It keeps moisture and dirt off the coil and holds the layers in transit.
Volgende stap
- Email us at info@fhopepack.com with your coil range, films and volumes.
- Binnen 48 uur sturen we u een voorstel voor de verpakking en een ontwerptekening.
- We arrange a site survey to confirm coil range and wrap needs.
Gerelateerd lezen
- Eenvoudige spoelwikkelaar
- Coilverpakking: technologie en beste praktijken
- Horizontal coil wrapping machine for automatic coil
- FHOPE verpakkingsmachine productlijnen
Bronnen en standaarden
- ISO 12100:2010 Veiligheid van machines, algemene principes voor ontwerp en risicobeoordeling
- EN 415-10:2014 Veiligheid van verpakkingsmachines, algemene eisen
- EN ISO 13849-1:2023 Veiligheid van machines, veiligheidsgerelateerde onderdelen van besturingssystemen
FHOPE vertical coil wrapping machine demonstration video. Reviewed as a general demonstration; coil range confirmed per project.
Laatst beoordeeld: 10-10-2026
