Samenvatting A 180° load inverter turns a stacked load upside down so the pallet ends up on top, for pallet exchange, for damaged bottom layers or for a process that needs the other face up. In this clip our ring-type inverter completes the turn in about 26 s. Our FPFZ-1 180° pallet inverter is specified for loads up to 1.2 t and about 50 s per turnover, configured per project.
Inhoudsopgave
- Wat de video laat zien, in de juiste volgorde.
- What a 180° load inverter does
- Turnover cycle time
- FPFZ-1 specifications
- Takt-controle
- Selection checklist for a 180° load inverter
- Bediening en veiligheid
- Veelgestelde vragen over techniek
- Volgende stap
- Gerelateerd lezen
- Bronnen
Wat de video laat zien, in de juiste volgorde.
The clip shows one machine from one camera position. It is a large white ring-type frame with a toothed ring on its outer face, carried on pairs of support rollers, with a blue geared motor at the lower left. The load is a stack of dark boards on a pallet, held between two inner support beams.
- 0 tot ongeveer 6 seconden. The ring is already turning, with the stack tilted at roughly 45° to 60°. A person crosses the background on the far side and does not approach the machine.
- Ongeveer 6 tot 12 seconden. The ring keeps turning and the stack passes the horizontal position.
- Ongeveer 12 tot 26 seconden. The ring completes the 180° turn. The stack is now upside down and the pallet sits on top, fully exposed. The motor runs without a visible pause.
What a 180° load inverter does
A load inverter clamps a stacked load between two platens or beams and rotates the whole package through 180°. Typical uses:
- Pallet exchange. Turn the load over, lift off the old pallet and set the load down on a new one, for example a plastic pallet for a clean area.
- Bottom-layer access. Damaged or wet bottom layers come to the top for removal.
- Process orientation. A board or sheet stack that needs its other face up for the next station.
The ring type in the clip turns on its outer ring and support rollers, so the load stays centred while it rotates and the frame needs no overhead structure.
| Inverter element | Afmetingen bepaald door |
|---|---|
| Inner beams or platens | Load footprint and stack height |
| Clamping travel | Height range of the load |
| Ring, gear ring and rollers | Load weight and centre of gravity |
| Motor met versnelling | Omzettijd |
Turnover cycle time
| Ga op de clip staan | Tijdsvenster | Duur |
|---|---|---|
| Turning, stack tilted | 0 tot ongeveer 6 seconden | ongeveer 6 sec |
| Passing horizontal | ongeveer 6 tot 12 seconden | ongeveer 6 sec |
| Completing 180°, pallet on top | ongeveer 12 tot 26 seconden | ongeveer 14 sec |
| Whole visible turn | 0 tot ongeveer 26 seconden | ongeveer 26 sec |
The clip starts with the ring already in motion, so clamping before the turn and unclamping after it are outside the 26 s. Our FPFZ-1 page quotes about 50 s per turnover, which is the figure we plan with.
FPFZ-1 specifications
| FPFZ-1 180° pallet inverter | Specificaties |
|---|---|
| Laad grootte | L1200 × W1100 to 1200 × H1200 to 2000 mm |
| Omzetcapaciteit | max. 1.2 t |
| Omzettijd | ongeveer 50 sec |
| Omslaghoek | 180 ° |
| Motorkracht | ongeveer 2.2 kW |
| Stroomvoorziening | 380 V, 50 Hz, three phase five wire |
| Werking | draadloze afstandsbediening |
Takt-controle
For an illustrative target of 30 loads per hour, the takt is 3,600 ÷ 30 = 120 s per load. At about 50 s per turnover there are about 70 s left for the fork-lift or conveyor to bring the load in and take it out. That is comfortable for one inverter. If the pallet is exchanged inside the cycle, add the time for that step.
Selection checklist for a 180° load inverter
- Load length, width and height range, with the pallet.
- Het gewicht van de lading en de stabiliteit van de stapel.
- Purpose: pallet exchange, bottom-layer access or face-up change.
- Loading method: fork-lift, pallet truck or conveyor.
- Floor space and clearance around the rotating ring.
- Takt, including clamping, the turn and unloading.
Bediening en veiligheid
The rotating ring, the support rollers and the gear ring are the danger zones. In the clip nobody comes near the ring while it turns. Keep everyone outside the rotating area while the inverter runs, and use the wireless remote from a position with a clear view of the whole ring.
Stop, isolate and lock out the inverter before anyone reaches into the ring or works on the load, and never leave a load clamped and turned with the drive isolated unless it is mechanically supported.
De geldende normen zijn afhankelijk van de bestemmingsmarkt. Voor CE-markten omvat EN 415-10 de algemene eisen voor verpakkingsmachines en stelt ISO 12100 de risicobeoordelingsmethode vast, die de beveiliging en de noodstopvoorziening regelt.
Veelgestelde vragen over techniek
Q: How long does a 180° turnover take? A: On the clip the visible turn takes about 26 s. Our FPFZ-1 page quotes about 50 s per turnover, which we use for takt planning.
Q: What load does the FPFZ-1 take? A: Up to 1.2 t and L1200 × W1100 to 1200 × H1200 to 2000 mm, turned 180°, with a 2.2 kW motor.
Q: Why turn a board stack over? A: To exchange the pallet, to bring damaged bottom layers to the top, or to present the other face to the next station.
Volgende stap
We size a 180° load inverter in three steps:
- Dien uw lay-outtekening in. with the load size, weight, purpose of the turn and takt, to info@fhopepack.com.
- Ontvang binnen 48 uur een offerte., including the clamping arrangement and the cycle check against your takt.
- Plan een locatiebezoek so we confirm the loading method, the floor and the clearance around the ring.
Gerelateerd lezen
- 180° pallet inverter FPFZ-1
- Spoelkantel- en kantelmachines
- Spoelkantelaar met schuiftafel
- Kantelaar en omkeerinrichting voor gepalletiseerde coils
Bronnen
- Inverter specifications: 180° pallet inverter FPFZ-1 product page
- Cliptiming: frametiming overgenomen uit de clip, 2 seconden tussen de frames
- De machine in actie: onze video op YouTube
- Toepassingsgebied van de normen: ISO 12100:2010, EN 415-10: 2014
Laatst beoordeeld: 05-10-2026
