kabel draad haspel verpakkingsmachines

Samenvatting This video shows a cable wire reel packing machine wrapping a fully wound cable reel in clear plastic film, then sealing and cutting it with an integrated heating unit. The full visible cycle runs from clamping through lift, film application, sealing, and release. The footage does not include loading, unloading, output rates, or technical specifications.

Anyone who ships or stores cable on reels knows the problem: a bare reel collects dust, absorbs moisture, picks up scratches, and arrives at the customer looking shop-worn. The machine shown in this video addresses exactly that step — the last one before a cable reel leaves production. It clamps the reel, lifts it into position, draws clear plastic film down over it, and heat-seals and trims the film in one sequence. Below, we walk through what the footage actually shows, what it does not show, and what a buyer should verify before committing to a purchase.

Wat de video laat zien: de machine in actie.

The video captures one complete packing cycle on a single machine, filmed from a fixed position. Here is how the sequence unfolds, based on sampled frames:

Later in the footage, a second reel — this one holding silver-grey metallic wire or strand — is shown already wrapped in film, clamped and stationary, in a post-sealing state. The indicator lights on the control cabinet have changed (red lit, green off), which appears to signal the machine’s status between cycles. No unloading action is filmed.

Directe observatie-aantekeningen

The following observations are kept close to the source analysis, with only grammar-level edits:

• The machine frame is painted steel: green base and yellow side panels and arms. A yellow top beam spans the working area.
• Central layout: a lift-type reel support (pneumatic or hydraulic), two laterally moving clamping arms with roller guides, an overhead film dispensing and sealing unit with guide rollers and a sealing knife, and a separate white control cabinet on the right.
• The control cabinet carries a three-color signal tower (red/yellow/green), several round push buttons with no visible text labels, and a raised red emergency-stop button with a protective cover at the lower right. No digital display or touchscreen is present.
• The workpiece is a black cable reel, multi-layer wound, roughly 60–70 cm in diameter and 40–50 cm high in proportion to the frame. A second reel with silver-grey metallic wire appears later, wrapped in transparent film.
• No physical guarding fence, safety light curtain, or interlocked door is visible. The only hazard marking is yellow/black striped tape on the floor near the base.
• Legible on-body text includes a Chinese brand marking on both yellow side panels, plus watermarks reading “FHOPEGROUP” and “www.fhopepack.com”. No model plate, parameter label, or certification mark is visible on the machine.
• No automatic loading or unloading is shown; the reel is placed on the support before filming begins and left in place after wrapping.

How it works: the packing sequence step by step

Breaking the cycle into its functional stages helps you compare this machine against alternatives:

1. Positionering. The reel rests on the central support with clamping arms open. Loading happens before the filmed cycle.
2. Clamping and lifting. The arms close on the reel’s edges, then the support raises the reel into the sealing zone. The order matters — clamp first, lift second — which suggests a simple sequenced control logic.
3. Folieapplicatie. Clear film feeds from overhead and drapes vertically over the reel’s circumference.
4. Sealing and cutting. Sealing components press closed, bond the film, and trim the surplus in the same action. Slight rotation of the reel helps the film sit evenly.
5. Vrijlating. The arms open, the support lowers, and the wrapped reel remains on the support for manual removal.

The integrated seal-and-cut step is the practical difference from a plain stretch-wrapping approach: the film is closed and trimmed by the machine rather than left loose for an operator to finish by hand.

Wat de video niet laat zien

Buyers should know the limits of the footage before drawing conclusions:

• No loading or unloading of reels — feeding and removal are handled outside the camera view.
• No cycle-time figures, power ratings, voltage, or frequency.
• No maximum reel diameter or weight limits.
• No film specification (material type or thickness).
• No safety certifications, model plates, or parameter labels on the machine.
• No demonstration of different reel sizes or changeover between them.
• No indication of automation options such as conveyor integration.

Any of these details matters to a purchase decision, so treat them as open questions for the manufacturer rather than assumptions.

Waar past dit type machine?

Based on the visible configuration — single-reel station, manual load, automatic wrap-seal-cut — the typical use cases are:

Compared with manual wrapping, the visible advantages are consistency of coverage, an integrated sealed edge, and reduced film waste from controlled dispensing. Compared with a fully automatic coil packing line, this machine relies on manual loading and unloading, which is the trade-off for a smaller footprint and simpler control panel.

Veiligheidsvoorschriften voor operators

The footage shows an open working area with no guarding. Whether you operate this machine or evaluate one:

• Keep hands clear of the clamping arms and lifting support during the cycle, especially during raise and lower.
• Confirm the red emergency-stop button (lower right of the cabinet, under a protective cover) is functional before each shift.
• Do not reach into the working zone while the film-sealing components are hot.
• If reel handling requires lifting equipment, use proper rigging rather than manual handling.

These points derive from what is visible in the video plus general industrial practice. Site-specific safety requirements should be confirmed with the manufacturer — see the verification list below.

Wat moet je controleren bij de fabrikant?

The video cannot answer these questions; ask before ordering:

1. Reel size range: minimum and maximum diameter and weight the clamping and lifting mechanism accepts, and how changeover works.
2. Film compatibility: which film materials and thicknesses the sealing unit handles, and whether sealing temperature is adjustable.
3. Cycle time per reel under realistic conditions.
4. Power supply requirements (voltage, frequency, air supply if pneumatic).
5. Control options: whether a display, fault diagnostics, or remote monitoring can be added.
6. Safety options: light curtains, guarding, or interlocks for your local compliance requirements.
7. After-sales support, spare parts availability, and commissioning/training.

Veelgestelde vragen

Does the machine wrap the reel automatically from start to finish? The wrap, seal, and cut steps run automatically once started, as shown in the video. Loading and unloading are not shown and appear to be manual. Check with the manufacturer for optional automation.

What kind of reel was packed in the video? A black cable reel, roughly two-thirds the width of the working area, plus a later reel of silver-grey metallic wire. Both were fully wound before filming.

Is there a display or touchscreen on the control panel? No. The panel shown has physical buttons, a three-color signal tower, and an emergency-stop button only. Any display or diagnostic capability would need to be confirmed with the manufacturer.

Can it handle different reel sizes? The video shows one size at a time and no changeover. The clamping arms move laterally, which suggests some adjustment range, but the actual limits must be verified with the manufacturer.

Is de machine voorzien van veiligheidsafscherming? No fence, light curtain, or interlock is visible in the footage — only floor marking tape. If your site requires guarding, raise it with the manufacturer.

Welke film wordt er gebruikt? The film is clear plastic, but its material and thickness are not identifiable from the video. Confirm the compatible film specification before purchasing.

Bron en methode

This article is based entirely on the video above. The footage was analyzed frame-by-frame using a vision model on sampled frames; the video contains background music only, with no narration or speech, so no transcript was used. Statements about machine capability beyond what is visible are explicitly marked as items to verify with the manufacturer.

Gerelateerd lezen

• Kabelverpakkingsmachine — the product family this machine belongs to.
• Draadspoelwikkelmachine — for wrapping wire coils rather than reels.
• Automatische spoelverpakkingslijn — a fully integrated line option.
• Automatische verpakkingslijn — end-to-end packaging automation.
• Stretch wikkelmachine — stretch-wrap alternatives for coil products.

Volgende stap

If the packing method shown here matches your product and volume, the fastest way forward is to send the manufacturer your reel dimensions, weight, and daily output requirements, and ask for the specifications listed in the verification section above. Visit the contact pagina to start that conversation or request a quote.