kabelspoelverpakkingsmachine en draadverpakkingsmachine;

Samenvatting

This short factory clip shows a cable/wire coil film-wrapping (packing) machine of the static-coil type: a black coil of wound wire or cable sits still on the machine’s support columns while an overhead arched arm draws stretch film from a top roll and spirals it around the coil, then presses the film end to finish the wrap. The footage runs about 49 seconds and includes a second wrapping cycle. Key point: the coil stays stationary and the wrapping mechanism rotates around it — the opposite geometry from a turntable wrapper. Eerlijke grens: no coil-size range, speed, film, power, or model data is shown — those must come from the supplier.

Alles hieronder is gebaseerd op wat daadwerkelijk in deze video te zien is. De tijdstempels zijn bij benadering (frames zijn elke twee seconden genomen uit de clip van ongeveer 49 seconden).

Directe observatie-aantekeningen

Deze structuurobservaties zijn rechtstreeks afkomstig uit de videobeelden. Alles wat niet in de beelden te lezen was, is als zodanig gemarkeerd.

  • Spoel: a black coil of tightly wound fine wire or cable, diameter roughly one and a half times the height of the machine’s support columns; it stays horizontal and stationary throughout.
  • Ondersteuning: two white support columns hold the coil in place in the center of the machine.
  • Arm inpakken: an arched metal arm (with yellow rollers) above the coil; it descends while film is fed from the top.
  • Filmrol: a transparent stretch film roll on a spindle at the top of the machine; film is pulled down and spiraled around the coil’s outer surface.
  • Frame: blue painted metal machine frame on a blue base; white/off-white supporting structures.
  • Controlepaneel: a blue control box on the right with a green start button, a red stop button, and further function buttons and indicator lights (indicators not lit in the footage).
  • People: an operator in blue workwear with white gloves makes a final adjustment/inspection at the end of the cycle.
  • Watermerk: het watermerk van de site www.fhopepack.com is visible at the bottom right throughout the footage.

Structuuranalyse van de machine

Bestanddeel Te zien in de video Wat het doet
Steunkolommen Two white columns in the center Hold the static coil during wrapping
Arched wrapping arm Metal arm with yellow rollers over the coil Presses and guides film around the coil
Film roll + spindle Bovenkant van de machine Supplies the transparent stretch film
Wikkelmechanisme Rotates around the stationary coil Wraps film spirally over the coil’s circumference
Bedieningspaneel Blue box with start/stop buttons Controls the cycle
Frame/basis Blue painted metal Supports the whole machine

The machine keeps the load stationary and moves the film-applying mechanism around it — a static-coil design.

What the video shows: the wrapping mechanism

Because the machine type is easy to confuse, it is worth restating how this unit works:

  • A black cable/wire coil is loaded onto the support columns and remains still.
  • The machine starts; the overhead arched arm moves down while transparent film is pulled from the top roll.
  • The film is applied in a tight spiral around the coil’s outer surface.
  • At the end, the film end is pressed down to seal the wrap; an operator performs a final check.
  • The footage then shows a second coil being wrapped the same way.

This contrasts with a turntable wrapper, where the load rotates. Here the coil is static and the wrapping mechanism rotates around it.

Wat de video niet laat zien

De video toont alleen het inpakproces. Het laat niet zien:

  • Coil size range — outer diameter, inner diameter, width, and weight.
  • Cycle time and throughput (coils per hour).
  • Number of film layers and film type/width.
  • Modelnummer, vermogen en spanning.
  • Rated load capacity of the machine.
  • Noodstop, afscherming of lichtschermen.
  • Certificeringen (CE, ISO).
  • Maintenance and noise/energy data.

Al deze gegevens moeten afkomstig zijn uit het specificatieblad van de fabrikant.

Opmerkingen van de operator

Human involvement is minimal and visible only at the end: an operator’s hand (blue workwear, white gloves) appears to adjust or check the finished wrap. Loading and starting are otherwise the only steps seen; the wrapping itself is automatic.

Geschiktheidscriteria

Staat van het product Check
Your product is a cable/wire (or similar) coil Confirm outer/inner diameter and width range
Coil can stay stationary on support columns This design does not spin the load
You want automatic film wrapping of coils Controleer het type film, de breedte en het aantal lagen.
Moderate packaging speed is acceptable Confirm cycle time at your coil size
You need hardened/guarded safety features Bevestig noodstop en bewakingspakket

Vragen van kopers

What coil sizes does the machine accept? Ask for the full outer/inner diameter, width, and weight range — none is shown in the video.

What is the wrap cycle time? Ask for coils per hour at your coil dimensions.

Hoe wordt de folie aangebracht en afgewerkt? The clip shows spiral wrapping with the film end pressed; confirm automatic start/cut and layer settings.

Does it handle my product’s weight? Confirm rated load capacity.

What safety and guarding are included? Only the start/stop control box is visible; confirm emergency stop, guards, and certifications.

Waarom dit zo belangrijk is

For cable and wire producers, a static-coil wrapping machine closes the packaging loop between manufacturing and shipping:

  • Consistente verpakking — each coil receives the same spiral film coverage.
  • Minder handarbeid — the machine wraps; staff supervise and finish.
  • Bescherming tijdens het transport — film keeps coils clean and stable during handling.
  • Simple footprint — one machine at the end of the coil line.

The coil stays put, so heavy or fragile coils are not spun during wrapping — relevant if your coils are large or sensitive to rotation.

Toepassingen waarvoor dit type machine geschikt is

Based on what the video shows (a black cable/wire coil being film-wrapped while stationary), this machine style is typically relevant to:

  • Cable and wire plants — packaged coils ready for distribution.
  • Similar coiled flexible products — hoses or wire-like coils that should not be rotated.
  • Coil end-of-line finishing — where a compact wrapping step is needed before palletizing.

Deze toepassingen zijn afleidingen uit de beelden, geen beweringen die in de video zelf worden gedaan.

Gerelateerd lezen

Bron en methode

Dit artikel is gebaseerd op de ingesloten demonstratievideo (YouTube ID). NjYD4olOG7s, about 49 seconds). Frames were sampled at two-second intervals and analyzed with a local vision model (Qwen3-VL), with a focused re-check of the later frames confirming a second wrapping cycle and that the coil is stationary while the mechanism rotates around it. The video contains background music only; there is no narration, so all observations are visual and timestamps are approximate. The derivative sections (applications, fit criteria, buyer questions, and evaluation) are clearly marked as analysis and are intended as a starting point for a conversation with a qualified supplier.

Volgende stap

Stuur uw coil outer/inner diameter, width, weight, and target output to the FHOPE sales team for a fit check on this static-coil cable/wire packing machine. Use the contact pagina om het gesprek te starten.

Laatst bijgewerkt: 31-08-2026.

gerelateerde berichten

Boek een gesprek
Boek een gesprek