Kopsavilkums
A hose or pipe coil needs a tight wrap so it stays clean and holds its shape, and a machine applies that wrap more evenly than hand wrapping. This machine loads the coil into a centre clamp, holds it with gripper arms and a top cylinder, and rotates it while a head lays the band in a spiral. The operator loads the coil and the machine does the wrapping and packing. Coil size, band width and wrap pattern are confirmed per project.
Saturs
- Why hose coils need machine wrapping
- Ko mašīna dara
- Saspiediet un pagrieziet
- Spiral along the axis
- Ko rāda videoieraksti
- Tipiski konfigurācija
- Atlases kontrolsaraksts
- Darbība un drošība
- Inženierijas bieži uzdotie jautājumi
- Nākamais solis
- Saistītā lasāmviela
- Avoti un standarti
Why hose coils need machine wrapping
A hose or pipe coil arrives from production wound, and it has to stay wound through storage and transport. A wrap band over the coil keeps the layers tight and the surface clean.
Wrapping a heavy coil by hand never applies the band evenly across the coil face. A machine that rotates the coil and feeds the band in a spiral gives the same result every time. Coil size and band are confirmed per project.
Ko mašīna dara
The machine is a coil wrapping machine for hose and pipe coils. The operator loads a coil into the centre clamp by hand. Gripper arms from both sides and a top cylinder then hold the coil in place. Once secured, the coil rotates while a wrapping head moves along the axis and lays a band over the surface in a spiral.
Because the coil is held and turned under power, the operator only loads and unloads the coil. The hold and rotation are confirmed per project.
Saspiediet un pagrieziet
After the operator steps back, the gripper arms close in from the sides and the top cylinder presses the coil against the rotation centre. The coil then turns steadily while the wrap is applied, so the band is drawn around the full circumference.
The clamp keeps the coil centred so the wrap is even on every side. Clamp force and rotation speed are confirmed per project.
Spiral along the axis
As the coil rotates, the wrapping head moves along the axis of the coil, so the band is laid in a spiral that covers the face of the coil from one side to the other. The footage shows the green band covering most of the circumference as the head travels.
The spiral lay means each pass overlaps the previous pass across the coil face. Head travel and overlap are confirmed per project.
Ko rāda videoieraksti
Our footage shows a coil wrapping machine loading a green hose or pipe coil, clamping it, and wrapping the band in a spiral as the coil rotates. It is a general demonstration, so your coil size, band width and wrap pattern are confirmed with us per project.
Tipiski konfigurācija
Zemāk redzamajos attēlos ir norādītas funkcionālās dizaina robežas, nevis skaitliskās vērtības, un tie tiek apstiprināti katram projektam.
| Parametrs | Tipisks diapazons, apstiprināts katram projektam |
|---|---|
| Slodze | hose or pipe coil |
| Turēt | gripper arms, top cylinder |
| Pagriezt | centre clamp drive |
| Wrap | band, spiral along axis |
| Guide | yellow grilles either side |
| Elektroapgāde | 380 V trīsfāžu 50 Hz vai 220 V vienfāzes vieglajām mašīnām, tiek izvēlēts katram projektam atsevišķi |
Atlases kontrolsaraksts
| jautājums | Apstiprināt katram projektam |
|---|---|
| Slodzes diapazons | spoles ārējais diametrs, platums, svars |
| Turēt | clamp, gripper, cylinder |
| Orķestris | width, tension, material |
| Wrap | head travel, overlap |
| Cikls | rotation speed, pass count |
| Elektroapgāde | spriegums, fāze un frekvence uz vietas |
Darbība un drošība
Load the coil, step clear, and start the cycle so the grippers and cylinder hold the coil while it rotates. Keep hands away from the holding area and the wrapping head while the machine runs, with the yellow safety grilles in place on both sides.
Routine checks cover the clamp, the gripper arms, the top cylinder and the wrapping head, per the machine manual. Confirm the wrap settings against the coil before each run.
Inženierijas bieži uzdotie jautājumi
Q: What does this machine do? A: It wraps hose and pipe coils by rotating the coil and laying a band in a spiral.
Q: Why hold the coil under power? A: Clamping keeps the coil centred so the wrap is even on every side.
Q: How is the band applied? A: A wrapping head moves along the axis while the coil turns.
Q: Does the operator wind it? A: No, the operator loads the coil and the machine does the wrapping.
Q: What keeps the coil centred during the wrap? A: The clamp holds the coil while the head travels, so each band stays even; clamp and travel are confirmed per project.
Nākamais solis
- Email us at info@fhopepack.com with your coil size.
- Mēs nosūtīsim ruļļa ietīšanas piedāvājumu un maketa rasējumu 48 stundu laikā.
- We arrange a site survey to confirm band width and wrap pattern.
Saistītā lasāmviela
- Coil wrapping machine for hose and pipe coils
- Šļūtenes spoļu ietīšanas mašīna
- Spolu tīšanas mašīnas
- FHOPE iepakošanas iekārtu produktu līnijas
Avoti un standarti
- ISO 12100:2010 Mašīnu drošība, vispārīgie projektēšanas principi un riska novērtēšana
- EN 415-10:2014 Iepakošanas mašīnu drošība, vispārīgās prasības
- EN ISO 13849-1:2023 Mašīnu drošība, ar drošību saistītās vadības sistēmu daļas
FHOPE coil wrapping machine for hose and pipe coils demonstration video. Reviewed as a general demonstration; coil size, band width and wrap pattern confirmed per project.
Pēdējoreiz pārskatīts: 2026-10-11
