Automatinis vamzdžių vyniojimo ir vamzdžių vyniojimo įrenginys

Name: Automatinis vamzdžių vyniojimo ir vamzdžių vyniojimo įrenginys
Uploaded: 2020-02-26T02:14:45+00:00
Duration: 1 min 46 s
Description: > **Executive summary** > Small plastic tube is sold in coils of a set length, so the coiler must wind it into neat layers and tie the coil before it leaves the line. > Our tube coiler does this on a yellow turntable under a vertical press head, on a…

Santrauka Small plastic tube is sold in coils of a set length, so the coiler must wind it into neat layers and tie the coil before it leaves the line. Our tube coiler does this on a yellow turntable under a vertical press head, on a blue and white frame, and straps the coil before it is taken off. The coil size follows from the vamzdžio ilgis ir vamzdžio išorinis skersmuoVisi nustatomi kiekvienam projektui.

Ką rodo vaizdo įrašas

A blue and white tube coiler stands in the workshop, with a red reel and yellow coil parts on its right. Tube runs in from the line and winds onto the yellow turntable, while the vertical press head above holds the coil.

Close-ups show the tube laying on the turning coil and the press head coming down. Finished blue tube coils lie beside the machine, and the fhopepack.com watermark runs along the foot of the clip.

How the tube coiler works

Žingsnis	Kas atsitinka,
Temos	The tube end is fixed on the turntable
ritė	The turntable winds the tube in layers
Skaičiuoti	The machine winds to the set length
Press and strap	The press head holds the coil while it is strapped
iškrauti	The tied coil is taken off the turntable

The press head keeps the layers flat, so the coil is even and the straps sit square. For coils that are film-wrapped after coiling, see our automatinė vamzdžių vyniojimo ir vyniojimo mašina.

Coil size and layer calculation

Each layer has a set number of turns across the coil width, and each layer adds two tube diameters to the OD. Illustrative example for 20 mm tube, 120 mm coil width and 400 mm ID:

Punktas	Reikšmė
Turns per layer, 120 ÷ 20	6
Layers for about 200 m (illustrative)	15
Coil OD, 400 + 2 × 15 × 20	1,000 mm
Mean diameter, 400 + 15 × 20	700 mm
Length, 6 × 15 × π × 0.7 m	apie 198 m

A longer coil adds layers and grows the OD, so we check the OD against your packaging and shipping limits.

Strapping the coil

Pasirinkimas	Ką tai nusprendžia
Dirželių skaičius vienoje ritėje	How well the layers hold in handling
Diržų padėtys	Even spacing round the coil
Dirželio įtempimas	Tight enough to hold, not so tight it crushes the tube
Paspauskite laikykite	Keeps the coil flat while strapping

Soft tube needs lower strap tension than rigid pipe, so we set tension on trial with your tube.

Valdikliai ir sauga

The turntable turns and the press head comes down with force. Keep hands clear of the turning turntable and out from under the press while it runs, and thread the tube only with the machine stopped.

Taikomi standartai priklauso nuo paskirties rinkos. CE rinkoms ISO 12100 nustato rizikos vertinimo metodą, o EN 415-10 nustato bendruosius pakavimo mašinų reikalavimus.

Selection checklist for a tube coiler

Tube OD, wall and material.
Coil length, ID and width.
Largest coil OD allowed.
Coils per hour from the extrusion line.
Straps per coil and strap type.
Grindų plotas ir maitinimo šaltinis.

Inžinerijos DUK

Q: How long a coil can it wind? A: It winds to the set length; our example of 15 layers of 20 mm tube is about 198 m.

Q: How does length change the coil OD? A: Each layer adds two tube diameters. In our example 15 layers on a 400 mm ID give about 1,000 mm OD.

Q: Why press the coil while strapping? A: The press head keeps the layers flat so the straps sit square.

Q: How tight should the straps be? A: Tight enough to hold, but soft tube needs less tension than rigid pipe; we set it on trial.

Q: What tube does it suit? A: Plastic tube and small pipe that can be wound on the turntable.

Kitas žingsnis

We plan your tube coiler in three steps:

Pateikite savo išdėstymo brėžinį with tube sizes, coil lengths and output to info@fhopepack.com.
Gaukite pasiūlymą per 48 valandas, su ritės dydžiu ir dirželio planu.
Užsisakykite objekto apžiūrą patikrinti ekstruzijos linijos išdėstymą.