Ritės pakreipiklis su stumdomu stalu: 90° pasukimas ir grįžimas

Santrauka A coil tilter with a sliding table turns a coil or packed load 90° and lets the table travel out for loading by crane or fork-lift. In this clip our C-shaped tilter turns a film-wrapped load from upright to on its side between about 16 s and 40 s, then swings it back by about 56 s. Our mechanical upender with sliding table is rated for 5 T, single-way 90° turn-over, about L3000 × W2200 × H2600 mm, configured per project.

Turinys

Kas rodoma klipe, eilės tvarka

The clip shows one machine from one camera position: a yellow C-shaped frame, open on one side, standing on a heavy blue base. A film-wrapped load sits inside the C. Each end of the frame has a round lifting lug.

  1. nuo 0 iki 12 s. The load rests upright on the table and nothing moves.
  2. Apie 16 sek. The frame starts to turn about its lower pivot and the load leans with it.
  3. Maždaug 20–32 s. The turn continues until the load lies on its side, held between the two arms of the C.
  4. Maždaug 36–40 s. The frame reaches the end of its turn, with the opening of the C facing up.
  5. Maždaug 44–56 s. The frame swings back and the load returns close to its upright starting attitude.

The table stays in its turning position throughout this sequence; table travel belongs to loading and unloading, before and after the turn.

What a sliding-table coil tilter does

A coil tilter turns a load through 90° between lying on its face and standing on its side. The sliding table adds one more function: the table on the base runs on rails, so it can travel out from under the frame for loading and unloading and travel back for the turn. That keeps the crane hook or the fork-lift away from the frame while the load is placed.

The C-shaped frame holds the load on two faces, the table and the back of the C. The load turns with the frame instead of sliding across it, which protects edges and film wrapping.

Tilter element Dydis pagal
C-frame opening Load height and width
Sliding table and rails Load footprint and loading method
Pivot and drive Load moment at 5 T
Kėlimo kilpos Moving and installing the frame

Turn and return cycle time on the clip

Užlipkite ant spaustuko Laiko langas Trukmė (dienos)
At rest before the turn Nuo 0 iki maždaug 12 s apie 12 s
Turn from upright to on its side apie 16–40 s apie 24 s
Return toward upright apie 44–56 s apie 12 s

The turn on the clip is slower than the return, which is usual: the drive slows the load into its side position, while the return carries less risk. Our page model is specified for a single-way 90° turn-over, where the frame turns the load once and the load leaves in its new attitude. The clip shows the frame returning, which is the two-way pattern. We choose one-way or two-way at the layout stage, because it changes the cycle.

Specifications of our sliding-table upender

Aukštyn ir pakreiptas su stumdomu stalu detalizavimas
Maks. pakrovimas 5 T
Apyvarta 90°, vienpusis
mašina dydis about L3000 × W2200 × H2600 mm
Mašinos svoris about 4 T
Maitinimo įtampa Kintamosios srovės 380 V, 60 Hz

Takto patikrinimas

For an illustrative target of 30 loads per hour, one load must leave every 120 s, from 3,600 ÷ 30. On the clip the turn takes about 24 s and the return about 12 s, about 36 s of motion. That leaves about 84 s for sliding the table out, unloading, loading, sliding it back and letting the load settle. When the table travel and the crane or fork-lift move fit in that window, one tilter covers the target.

Selection checklist for a coil tilter with sliding table

  • Load OD, width or footprint, and weight up to 5 T.
  • Atvykimo nuostata ir nuostata, kurios reikia kitai stočiai.
  • One-way turn-over, or turn and return.
  • Loading method: crane, fork-lift or conveyor, and the table travel needed.
  • Floor space for about L3000 × W2200 × H2600 mm, plus the table travel, which we fix at the layout stage.
  • Takt, including table travel and loading.

Valdikliai ir sauga

The swing of the C-frame and the travel of the sliding table are the danger zones. Keep everyone outside both while the tilter runs, and load only with the table in its loading position and the frame at rest. Stop, isolate and lock out the tilter before anyone works on the load, the table or the rails, and never leave a load turned with the drive isolated unless it is mechanically supported.

Taikomi standartai priklauso nuo paskirties rinkos. CE rinkose EN 415-10 apima bendruosius pakavimo mašinų reikalavimus, o ISO 12100 nustato rizikos vertinimo metodą, kuriame nustatomi apsaugos ir avarinio stabdymo įtaisai.

Inžinerijos DUK

Q: Why add a sliding table to a coil tilter? A: The table travels out from under the frame on rails, so the crane or fork-lift places the load clear of the C-frame. The table then travels back and the frame turns the load 90°.

Q: What load does the sliding-table upender take? A: Our page model is rated for 5 T, with a single-way 90° turn-over and a machine size of about L3000 × W2200 × H2600 mm.

Q: How long does the turn take? A: On the clip the turn takes about 24 s and the return about 12 s. Add table travel and loading time before comparing with your takt.

Kitas žingsnis

We size a sliding-table coil tilter in three steps:

  1. Pateikite savo išdėstymo brėžinį with the load size, weight, turn angle, loading method and takt, to info@fhopepack.com.
  2. Gaukite pasiūlymą per 48 valandas, including the frame and table arrangement and the cycle check against your takt.
  3. Užsisakykite objekto apžiūrą so we confirm the foundation, the table travel and the clearance around the frame.

Šaltiniai

Paskutinį kartą peržiūrėta: 2026-10-05

Susijusios Žinutės

Užsisakykite skambutį
Užsisakykite skambutį