회사 개요
A 180° sheet turnover machine—also called a plate flipping machine—turns steel and metal sheets from one face to the other without lifting them off the line. Instead of swinging the load on a crane and risking the face and the edge, the machine feeds the sheet into a rotating ring, grips it, and turns it in place: the ring rotates 180° and the sheet comes out on its other face. This guide is written for the production engineers, plant managers and equipment buyers in sheet-metal forming, plate processing and stamping shops, and covers how a ring-type turnover machine works, which steel and metal sheets it suits, and what you need to specify for a custom machine.
The video below shows a 180° sheet turnover machine flipping steel and metal sheets:
Why Use a Turnover Machine Instead of a Crane
Flipping a sheet with a crane is slow and risky for the sheet: the load swings as its weight shifts over the edge, and the edge that takes the load can chip or dent. A turnover machine removes the swing and turns the sheet in place.
| 접근 | Sheet protection | Labour and speed |
|---|---|---|
| Crane with rigging | Load swings; the edge that takes the weight can be damaged | Needs two or more operators and careful rigging |
| Manual floor tipping | Sheet drags and can pick up debris | 느리고 육체적으로 힘들다 |
| 180° turnover machine | Sheet is gripped and rotated in place; no swing, no floor drag | One operator; controlled cycle |
The machine is built for production: it flips the sheet in a repeatable cycle that can be synchronised with the stations upstream and downstream.
How a Ring-Type 180° Turnover Machine Works
The machine uses a large ring frame carried on rollers in a heavy base. The sheet is loaded into the open centre of the ring, gripped, and the whole ring—with the sheet—rotates about a horizontal axis. After a 180° rotation the sheet is on its other face at the same height, ready to leave:
| 단계 | 무슨 일이 |
|---|---|
| 먹이 | The sheet enters the open centre of the ring by forklift, crane or conveyor. |
| 직책 | The sheet is supported so it does not sag or shift before the turn begins. |
| 손잡이 | The machine engages the sheet—edge clamps or clamping frame members hold it against the support—so the turn is controlled. |
| 회전 | The ring rotates 180° about the horizontal axis, turning the sheet over in place. |
| 해제 | The sheet is released and leaves the ring on its other face, at the same working height. |
Because the sheet turns inside the ring, both faces are protected: the load does not swing, the edge is not forced against a hard pivot, and the sheet never slides across the floor or another sheet.
Which Steel and Metal Sheets Suit a Custom Machine
A custom machine is sized to your product. The variables the manufacturer needs are the same whether the part is a steel plate, a stainless sheet or a metal sheet for further forming:
| 입력 | 중요한 이유 |
|---|---|
| Part type and shape | Steel plate, stainless sheet or other metal sheet changes the grip and support build. |
| 길이, 너비 및 두께 | Set the ring opening, support positions and clamp span. |
| Heaviest part weight | Sets the ring drive rating and the flipping load. |
| 표면 마무리 | A polished or coated surface may need padded contact at the grip points. |
| Turn requirement | Full 180°, or a stop at an intermediate angle for inspection. |
| Infeed/outfeed and parts per shift | Sets the access height, cycle time and line integration. |
This machine family builds both mechanical upenders (product-line range roughly 1–60 tonnes) and heavy-duty hydraulic configurations (product-line range roughly 1–100 tonnes), so the rating is selected from your heaviest part rather than chosen from a stock frame.
공장 테스트 및 승인
Because the machine is custom and handles heavy sheet, confirm what was tested before it ships:
- 장기 달리기 기록. A test log covering near-continuous cycling (the maker’s stated protocol for this machine family runs up to about 24 hours), stated as unloaded or under load.
- Drive and hold record. Evidence the machine rotated to the required angle and held position without drift.
- Safety device verification. Sign-off that the guards, safety interlocks and the emergency stop work as designed, keeping operators clear of the moving ring.
- Power-loss behaviour. Confirmation that a simulated power loss stopped and held the ring safely without dropping or slipping the sheet.
- 규정 준수 관련 문서. Confirmation of the safety references used for this machine family (EN 415-10 as reference and an ISO 12100 risk assessment).
- 시운전 범위. A clear written definition of installation support, commissioning and local on-site service where available.
On arrival, repeat the core checks on your floor—empty rotation, a loaded turn at your rated weight, the emergency stop, and the power-loss stop—before bringing the machine into production.
FAQ
Q: Is a 180° turnover machine the same as an upender? A: In this family they share the same product line. A 180° turnover machine produces a full face change by rotating the sheet inside a ring; an upender or tilter may turn through a set angle such as 90°. State your turn requirement when ordering.
Q: Can it handle stainless steel without marking the surface? A: Yes, if the grip and support are built for it. Stainless and polished sheets are normally turned with padded contact; confirm this on the approval drawing.
Q: What happens if power fails mid-turn? A: The machine’s safety design stops and holds the ring in position; when power is restored the control system resumes safely rather than dropping the sheet.
Q: How fast is a typical turn? A: Cycle time depends on part weight and the speed setting. The manufacturer states the turn time for your part in the proposal, so you can compare it with your shift budget.
질문: 어떤 안전 기준이 적용되나요? A: The machine family is built to CE requirements, with EN 415-10 as the reference and an ISO 12100 risk assessment covering the swept area of the moving ring.
다음 단계
Send your sheet type and size, heaviest weight, turn requirement, infeed/outfeed method and parts per shift, so a custom 180° turnover machine can be sized, specified on the approval drawing, and tested to an agreed list before shipment.
관련 자료
- 코일 업엔더 및 산업용 회전 솔루션 – Custom mechanical (≈1–60T) and hydraulic (≈1–100T) turnover equipment.
- Hydraulic Upender and Tilter Solutions – Manufacturer’s declared pre-delivery testing practice and control/safety verification.
- 180° 회전 기계는 프리캐스트 부품 및 판재 가공에 어떻게 작동할까요? – 180° turning machine kinematics and EN 415-10 / ISO 12100 safety references.
