**Sintesi esecutiva**
>
> A mold flipper lift table is a hydraulic table that lifts one plate through 90° to turn a heavy mold onto its side. A folding bellows guard closes the gap under the rising plate. Our FPMT-10 handles molds up to 10 t and our FPMT-30 up to 30 t; each flip takes 15–30 s. A worked example finds the balance point of a 12 t mold and the model it needs.
Sommario
- What the lift table does
- Why the bellows guard matters
- The balance point of a turning mold
- FPMT model data
- Worked example: a 12 t mold
- Applicazioni
- Lista di controllo per la selezione
- Sicurezza: EN 415-10 e ISO 12100
- FAQ di ingegneria
- Passo successivo
- Lettura correlata
- fonti
What the lift table does
The machine is a long, low green table on the shop floor, with its control panel at one end. A large mold is set on the table by crane. At the press of a button, one half of the table rises on hydraulic cylinders, pivoting near the middle, and the mold turns with it until it stands on its side. The plate then comes back down, and the table is flat and ready for the next mold.
Turning a mold this way replaces flipping it on crane chains (see [why 90° mold upenders are replacing overhead cranes](https://www.fhopepack.com/videos/the-roi-of-safety-why-90-degree-mold-upenders-are-replacing-overhead-cranes-in-industrial-toolrooms/)), where the mold can swing and land hard. The flip is slow and controlled, and the mold is supported on a plate the whole time.
Why the bellows guard matters
As the plate rises, it opens a wedge-shaped gap above the base. A hand or foot in that gap would be crushed when the plate comes down. Our table closes the gap with a black folding bellows guard. It is folded flat against the side of the table when the plate is down. As the plate lifts, it opens into a fan that covers the whole wedge, and it folds back as the plate returns.
The balance point of a turning mold
The load on the cylinders changes through the flip. At the start, the mold's weight acts at its centre of gravity, out from the pivot, so the cylinders carry the largest turning load. As the plate rises, the centre of gravity moves towards a point above the pivot, and the load falls.
At the balance angle, it is directly above the pivot. Past that angle, the mold wants to tip onto its new face. The hydraulic circuit then has to hold the load back, so the plate lowers the mold instead of letting it fall. We set the valve arrangement for this over-centre stage to the mold weight, and confirm it at quote.
For a mold sitting tight against the pivot, the balance angle is θ = arctan(x ÷ y). Here x is the distance from the pivot to the centre of gravity along the plate, and y is the height of the centre of gravity above the plate. The turning load is M = m × g × r × cos(θ + φ), where r = √(x² + y²) and φ = arctan(y ÷ x).
FPMT model data
| Item | FPMT-10 | FPMT-30 |
| :--- | :--- | :--- |
| Max load | 10 t | 30 t |
| Table L × W × H | 3,000 × 2,000 × 400 mm | 3,500 × 2,500 × 450 mm |
| Motor power | confirmed at quote | confirmed at quote |
| Rotation | 90° | 90° |
| Flip cycle | 15–30 s | 15–30 s |
We size the drive with a 20% allowance over the rated load. Both tables are built to the mold, and we also build 180° flippers.
Worked example: a 12 t mold
Illustrative mold: 12 t, 1,600 mm long along the lifting plate and 1,200 mm high, set tight against the pivot, with its centre of gravity at its centre.
| Verifica | Calcolo | Risultato |
| :--- | :--- | :--- |
| Rated load needed | 12 t is already over the FPMT-10's 10 t; with 20% allowance, 12 × 1.2 | 14.4 t, so FPMT-30 |
| Footprint | 1,600 mm on a 3,500 × 2,500 mm table | fits |
| x, y | 1,600 ÷ 2, 1,200 ÷ 2 | 0.8 m, 0.6 m |
| Balance angle | arctan(0.8 ÷ 0.6) | ≈ 53° |
| Turning load at the start | 12,000 × 9.81 × 0.8 | ≈ 94 kN·m |
| Turning load at 53° | centre of gravity above the pivot | 0 |
**Result.** The 12 t mold is over the FPMT-10's rating before any allowance, so it goes on the FPMT-30. The cylinders carry about 94 kN·m at the start, and the load falls to zero at about 53°. From 53° to 90° the mold leans onto its new face, so the plate lowers it the last 37° under control. A taller mold has a lower balance angle and tips over sooner.
Applicazioni
- Turning injection and die-casting molds for maintenance and polishing.
- Opening and closing heavy molds for inspection.
- Turning dies, castings and heavy fixtures before machining.
Lista di controllo per la selezione
1. Mold weight, with 20% allowance.
2. Mold length, width and height, and the shape of its base.
3. Turning angle: 90° or 180°.
4. Crane or forklift loading.
5. Floor space and power supply.
Sicurezza: EN 415-10 e ISO 12100
We design the table to EN 415-10 and assess its risks to ISO 12100. The main hazard is the crush gap under the rising plate, which the bellows guard closes. The operator works from the panel at the end of the table, clear of the plate and the mold.
FAQ di ingegneria
Q: Why does the shape of my mold matter?
A: The table is sized to the mold base. The table size also drives the cost, so we ask for the mold shape before quoting.
Q: How long does one flip take?
A: 15–30 s, depending on the mold weight and the table.
Q: Can it turn a mold through 180°?
A: This table turns 90°. We build 180° mold flippers as well.
Q: What happens past the balance point?
A: The mold leans onto its new face. The hydraulics hold it back, and the plate lowers it the rest of the way.
Q: Does the table need a pit?
A: The table shown stands on the shop floor at 400–450 mm high. Floor loading and anchoring are checked against your mold weight in the layout.
D: Quale norma si applica?
A: Norma EN 415-10 per la macchina e norma ISO 12100 per la valutazione del rischio.
Passo successivo
1. **Send mold weight, size and base shape** to info@fhopepack.com.
2. **We size** the table and the drive.
3. **Rispondiamo entro 24 ore** con un progetto e un preventivo.
Lettura correlata
- [90 degree mold flipper for 10T (product)](https://www.fhopepack.com/mold-flipper/90-Degree-Mold-Flipper-for-10T.html)
- [90 degree mold flipper for 30T (product)](https://www.fhopepack.com/mold-flipper/90-Degree-Mold-Flipper-for-30T.html)
- [Mold flipper table, 180° (product)](https://www.fhopepack.com/Hydraulic/mold-flipper-table.html)
- [Why 90 degree mold upenders are replacing overhead cranes](https://www.fhopepack.com/videos/the-roi-of-safety-why-90-degree-mold-upenders-are-replacing-overhead-cranes-in-industrial-toolrooms/)
- [Big frame flipper for 180 degree turning](https://www.fhopepack.com/videos/big-frame-flipper-for-180-degree-turning/)
fonti
- FHOPE product pages: 90 degree mold flipper for 10T and 30T; mold flipper table
- FHOPE project notes on mold flipper enquiries
- Our mold flipper lift table shown above
- Worked example: illustrative figures; g = 9.81 m/s²
- Norme: EN 415-10; ISO12100:2010
Ultimo aggiornamento: 19/10/2026
