> **Ringkasan Eksekutif**
> Dies, moulds and other heavy blocks often have to be turned 90 degrees for maintenance, inspection or storage, and doing it with a crane and chains is slow and risky.
> Our die mould upender and tilter in this video takes the load on an orange tilting cradle on a green base and turns it toward vertical.
> Whether a load can be turned follows from its **weight** and **centre of gravity**. We check both per project.
Daftar Isi
- Apa yang ditunjukkan video tersebut
- Cara kerja dudukan miring
- Memeriksa beban
- Di mana alat pembalik cetakan membantu
- Kontrol dan keamanan
- Daftar periksa pemilihan untuk alat pembalik cetakan die
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- sumber
Apa yang ditunjukkan video tersebut
Mesin pengangkat barang kami berdiri di aula pabrik: alas hijau yang menopang dudukan miring berwarna oranye dan merah, dengan merek FHOPE GROUP pada mesin tersebut. Muatan berbentuk kotak besar diletakkan di dudukan tersebut.
Dudukan mesin ditampilkan dari berbagai sudut, dimiringkan ke arah vertikal, dan kemudian diturunkan rata dan kosong. Seorang pekerja dengan pakaian kerja biru berdiri di latar belakang aula, menjauh dari mesin. Logo FHOPE GROUP juga muncul sebagai lapisan tambahan pada klip tersebut.
Cara kerja dudukan miring
| Langkah | Apa yang terjadi |
|---|---|
| Load | The load is set on the cradle |
| Secure | The load is held against the cradle faces |
| Tilt | The cradle turns the load toward vertical |
| Unload | The turned load is lifted off |
| Return | The cradle goes back to flat |
Beban bertumpu pada dua sisi dudukan selama putaran, sehingga beban ditopang sepenuhnya dan tidak tergantung pada pengait.
Memeriksa beban
Contoh ilustratif untuk cetakan baja:
| Barang | Nilai |
|---|---|
| Length × width × height (illustrative) | 1,200 × 800 × 600 mm |
| Volume, 1.2 × 0.8 × 0.6 | 0.576 m³ |
| Steel density | 7,850 kg/m³ |
| Weight if solid, 0.576 × 7,850 | about 4,522 kg |
Cetakan asli dengan rongga di dalamnya memiliki bobot lebih ringan. Kirimkan kepada kami berat cetakan dan gambarnya, dan kami akan memeriksa ukuran dudukan dan pusat gravitasinya.
Di mana alat pembalik cetakan membantu
| Use | What the turn does |
|---|---|
| Mould maintenance | Presents the parting face for cleaning and repair |
| Die change | Turns the die to the press orientation |
| Inspection | Shows the underside without a crane flip |
| Storage | Stands moulds upright to save floor space |
Turning on a cradle replaces crane flips, where the load swings and lands on its edge. For round loads, see our [multipurpose automatic coil tilter with slide table](https://www.fhopepack.com/videos/multipurpose-automatic-coil-tilter-with-slide-table/) and our [large and long coil upenders](https://www.fhopepack.com/videos/large-and-long-coil-upenders-in-real-world-operation/).
Kontrol dan keamanan
The cradle turns a heavy load. Keep people clear of the cradle and the load's path while it tilts, and stand away from the machine as the worker in our video does.
Standar yang berlaku bergantung pada pasar tujuan. Untuk pasar CE, ISO 12100 menetapkan metode penilaian risiko dan EN 415-10 menetapkan persyaratan umum untuk mesin pengemasan.
Daftar periksa pemilihan untuk alat pembalik cetakan die
- [ ] Heaviest die or mould weight.
- [ ] Length, width and height of the largest load.
- [ ] Centre of gravity position.
- [ ] Turning angle needed.
- [ ] How the load arrives: crane or forklift.
- [ ] Luas lantai dan pasokan listrik.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: What does a die mould upender do?
A: It turns a heavy die or mould toward vertical on a tilting cradle instead of a crane flip.
Q: How do you estimate the weight of a solid steel mould block?
A: Volume times steel density: about 4,522 kg for 1,200 × 800 × 600 mm at 7,850 kg/m³ in our example; a mould with cavities weighs less.
Q: Why is a cradle safer than a crane flip?
A: The load rests on two faces during the turn instead of swinging on a hook.
Q: What should I send for sizing?
A: The heaviest mould weight, its drawing and centre of gravity.
Q: Does anyone stand at the machine during the tilt?
A: No. Keep clear of the cradle and the load's path.
Langkah selanjutnya
Kami merencanakan alat pembalik cetakan die Anda dalam tiga langkah:
1. **Submit your layout drawing** with mould weights, sizes and drawings to **info@fhopepack.com**.
2. **Receive a proposal within 48 hours**, with the cradle size and load check.
3. **Book a site survey** to check crane or forklift access and floor space.
Bacaan terkait
- [Mould upender](https://www.fhopepack.com/mold-upender/)
- [Mould flipper](https://www.fhopepack.com/mold-flipper/)
- [Video: why 90-degree mould upenders are replacing overhead cranes](https://www.fhopepack.com/videos/the-roi-of-safety-why-90-degree-mold-upenders-are-replacing-overhead-cranes-in-industrial-toolrooms/)
sumber
- Konten mesin: Tim teknik FHOPE, 10 Oktober 2026
- Load example: our worked example, illustrative values; steel density 7,850 kg/m³
- Machine in action: [our video on YouTube](https://www.youtube.com/watch?v=AVza0eNbc7o)
- Cakupan standar: [ISO 12100:2010](https://www.iso.org/standard/51528.html), [EN 415-10:2014](https://www.nen.nl/en/nen-en-415-10-2014-en-191845)
Terakhir ditinjau: 04-10-2026
