mesin pengemasan film gelembung kabinet-FHOPE Packaging Machinery

Ringkasan Eksekutif

A cabinet bubble film packing machine covers each cabinet in bubble film as it travels on a conveyor, so lacquered and veneered faces are cushioned before they are wrapped or boxed. Ours combines a bubble film covering device with conveyors and, where needed, an orbital stretch wrapper, for cabinets 1,500–2,800 mm long and 20–100 kg. A worked example estimates film use and output.

Daftar Isi

Why cabinets are covered in bubble film

Kitchen cabinets, wardrobe carcasses and furniture panels leave the factory with finished faces. In a carton or a truck, edges rub and corners take knocks. Stretch film alone holds the pack together but gives little cushion. A layer of bubble film first takes the knocks and keeps the film off high-gloss surfaces.

By hand, covering a long cabinet takes two people and the result varies. A covering machine does it in line, the same way every time.

Inline bubble film covering machine construction

Our covering machine is a steel-framed tunnel over a powered roller and belt conveyor. The cabinet, a long black box here, runs in on the belts. Bubble film is drawn from a roll above and laid over the top and sides as the cabinet passes.

White pressing rollers with yellow rims hold the film down on the cabinet, and side guide rollers fold it round the edges. A head on the red arm seals and cuts the film between cabinets. The control box sits at the side of the line.

How a cabinet is covered

  1. Umpan masuk. The cabinet enters on the roller conveyor, centred by the side guides.
  2. Penutup Bubble film is pulled over the cabinet and pressed onto it by the upper rollers.
  3. Melipat. The side rollers bring the film down round the edges.
  4. Segel dan potong. The film is sealed and cut behind the cabinet.
  5. Keluaran. The covered cabinet moves on to stretch wrapping, cartoning or the pallet.

Cabinet size range

Size range of our cabinet and closet wrapping line:

Barang Jarak
Panjang objek 1,500 – 2,800 mm
Object width 650 – 1,220 mm
Object thickness 200 – 800 mm
Berat 20–100 kg
Modul otomatisasi corner feeder, 90° transfer
End sealing optional head and tail covering for a 6-sided seal

Film width, line speed and power are set for your cabinet mix and confirmed at quote.

Worked example: film and output for a wardrobe panel

Illustrative cabinet: 2,000 mm long, 700 mm wide, 400 mm thick, 45 kg.

Pengecekan kecocokan. All sizes are inside the ranges above.

Film to go round. The film must cover the girth: 2 × (700 + 400) = 2,200 mm. With a 100 mm overlap at the seal, the film needs 2,300 mm across the cabinet.

Film per cabinet. Covering the 2,000 mm length plus 200 mm at each end for folding gives 2.4 m of travel. Film area ≈ 2.3 × 2.4 ≈ 5.5 m² per cabinet.

Keluaran. At a conveyor speed of v m/min and a gap g between cabinets, output is 60 × v ÷ (L + g) cabinets per hour, with L and g in metres. The line speed is matched to the upstream cycle and confirmed at quote, together with the film roll size, film thickness and the seal and cut method.

Langkah Rumus Hasil
Ketebalan 2 × (W + T) 2,200 mm
Film across girth + overlap 2,300 mm
Film along L + 2 × end fold 2.4 m
Film area across × along 5.5 m²

Opsi garis

  • Orbital stretch wrapper after the cover. The stretch film holds the bubble layer tight for export.
  • Head and tail covering. Closes both ends for a dust-proof 6-sided pack.
  • Corner feeder and 90° transfer. For a hands-free link to the production line.
  • Cartoning. The covered cabinet goes straight into a box.

Daftar periksa pemilihan

  1. Cabinet length, width, thickness and weight range.
  2. Surface finish: high gloss, veneer or melamine.
  3. Cabinets per hour.
  4. Bubble film only, or bubble film plus stretch wrap.
  5. End covering needed or not.
  6. Country of installation, for voltage and CE.

Keamanan: EN 415-10 dan ISO 12100

We build the line to EN 415-10, with an ISO 12100 risk assessment. The hazards are the pressing rollers, the conveyor nip points, and the hot seal and cutting head. Guards cover the seal head, and the line stops when a guard is opened. Film roll changes and jam clearing are done with the line stopped.

Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik

Q: Will the rollers mark a high-gloss finish? A: The rollers press on the bubble film, not on the cabinet face. We set the pressure for the finish.

Q: Can the same machine cover doors and panels? A: Yes, if they sit inside the size range. Thin parts need the guides set closer.

Q: Do we still need stretch film? A: For local delivery the bubble cover may be enough. For export we add an orbital stretch wrapper to hold the cover tight.

Q: Which standard applies? A: EN 415-10 for the packaging line, with the risk assessment to ISO 12100.

Langkah selanjutnya

  1. Send your cabinet sizes, weights and finish Kirimkan ke info@fhopepack.com.
  2. We match the covering and wrapping modules.
  3. Kami membalas dalam waktu 24 jam with a line layout.

sumber

  • FHOPE bubble film wrapper and cabinet and closet orbital wrapping machine pages
  • Our bubble film covering machine shown above
  • Contoh soal: gambar ilustrasi
  • Standar: EN 415-10; ISO 12100:2010

Terakhir ditinjau: 18-10-2026

Pesan Panggilan
Pesan Panggilan