Ringkasan Eksekutif
Doors leave the plant either in a tight film shell that survives transit, or with scratched faces and torn corners. Door shrink wrapping closes each door in film on three sides, then shrinks the film tight in a hot-air tunnel, so every door is sealed the same way. This page compares the three sealer layouts we build, shows how to size the machine to your door widths, and covers film choice and line length.
Two operators lay a door panel onto the green infeed table, where it runs into the sealing station and is closed in film, as on our panel sealing and shrinking machine. The sealed door then travels on the red roller conveyor of the shrink tunnel, which carries it through the hot air and out with the film pulled tight.
Daftar Isi
- Why doors need a sealed shell
- How three-side sealing works
- Three sealer layouts
- Data mesin
- Sizing to your door widths
- Daftar periksa pemilihan
- Safety/keselamatan
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- sumber
Why doors need a sealed shell
Doors are shipped by the stack and moved by hand on site. Painted and laminated faces scratch at the first contact, and corners chip. Cardboard corners help but leave the faces open. A shrink shell covers every face and corner, keeps out dust during storage and is fast to remove at installation.
How three-side sealing works
- Masukan: the door is placed on the infeed table between guide plates.
- Tutupi: upper and lower film meet in front of the door, and the door pushes into the film.
- Segel: each cycle makes three seams: the cross seal at the back edge and the two side seals along the long edges. The front is already closed where upper and lower film were joined in the previous cycle.
- Menyusut: the door passes through the tunnel on a roller conveyor; hot air shrinks the film tight.
- Umpan keluar: the shrunk door cools on the outfeed rollers and is stacked.
Three sealer layouts
| tata ruang | How sides are closed | Terbaik untuk |
|---|---|---|
| One sealer with two press devices | nip rollers press the side film | single doors, standard sizes |
| Three cutters | separate cutter on each side | stacked doors, large goods; smoother edges |
| Penyegel gerak | heat-sealing knives on both sides, guide plates on the conveyor | smooth-surfaced doors in varying sizes |
Data mesin
| Barang | FHOPE door shrink packing machine |
|---|---|
| Panjang objek | 1,000 – 4,000 mm |
| Lebar objek | hingga mm 1,200 |
| Tinggi meja kerja | tentang 800 mm |
| Kecepatan konveyor | sekitar 4–9 m/menit |
| Film | PE, POF or PVC with vent holes |
| Ketebalan film | 80–150 μm recommended; 200 μm available |
| kontrol | PLC dan HMI |
Single-door thickness, stack height and wider doors are confirmed at quote.
Sizing to your door widths
Size the machine to the widest door you pack often, not the widest door you ever make. On one Australian project, doors were up to 1,500 mm wide, but 90% were under 1,200 mm. The customer also had limited floor space. A machine for 1,200 mm covered most of the output in a smaller footprint, and the few wider doors needed a separate solution.
Line length ≈ infeed + sealer + tunnel + cooling outfeed. The infeed and outfeed tables must be longer than your longest door; the sealer frame length depends on the sealing stroke.
Doors per hour ≈ conveyor speed × 60 ÷ (door length + gap). At 6 m/min with 2.1 m doors and a 0.4 m gap, that is about 6 × 60 ÷ 2.5 = 144 doors per hour (example only).
Daftar periksa pemilihan
- Minimum and maximum door length, width and height?
- Share of output by width?
- Single doors or stacks?
- Jenis dan ketebalan film?
- Floor length available?
- Doors per hour?
Safety/keselamatan
We design shrink lines to EN ISO 12100:2010 for risk assessment, EN 415-10 for packaging machine safety and EN 60204-1 for electrical equipment. The sealing knives and hot tunnel are the main hazards; sensors control the sealing and the tunnel is guarded.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: Shrink or stretch wrapping for doors? A: Shrink is faster, uses less material and has fewer size limits than a horizontal stretch wrapper, because it covers every face in one layer without spiral overlaps.
Q: Which layout gives the neatest edges? A: Three cutters or the motion sealer; cutters leave fewer wrinkles than nip rollers.
Q: Can it pack stacked doors? A: Yes, the three-cutter layout suits stacks.
Q: What do you need for a three-side quotation? A: Minimum and maximum length, width and height of the doors.
Langkah selanjutnya
- Send your door sizes, output and floor plan Kirimkan ke info@fhopepack.com.
- Kami memilih the sealer layout and tunnel length.
- Kami membalas dalam waktu 24 jam dengan proposal dan penawaran harga.
Bacaan terkait
- Automatic door shrinking machine (product)
- Mesin pengecil pintu dengan penyegel gerak (produk)
- Door panel sealing and shrinking machine (video)
- Door and panel shrink packaging machine (video)
sumber
- FHOPE product pages: automatic door shrinking machine; door shrinking machine with motion sealer
- FHOPE project correspondence on door shrink packing
- EN ISO 12100:2010; EN 415-10; EN 60204-1
- The door shrink wrapping line shown above
Terakhir ditinjau: 20-10-2026
