Ringkasan Eksekutif
An advanced auto aluminum ingot cross strapping machine applies steel straps across a stacked ingot block so the load holds together in transit. The stack is carried under a gantry frame, and a strapping head lowers onto the stack to apply the cross straps. Stack height, strap type and cycle time are confirmed per project.
Daftar Isi
- Why cross strap ingot stacks
- Apa yang dilakukan mesin itu
- Gantry frame and strapping head
- Strapping cycle and control
- Apa yang ditunjukkan oleh rekaman tersebut
- Konfigurasi khas
- Daftar periksa pemilihan
- Operasi dan keamanan
- Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
- Langkah selanjutnya
- Bacaan terkait
- Sumber dan standar
Why cross strap ingot stacks
Aluminum ingot stacks travel between the smelter, storage and transit, and a loose stack can shed ingots or tilt as it is moved. Cross straps hold the ingots square in one block, so the stack stays put under handling.
Strapping by machine applies the straps in a repeatable pattern instead of relying on manual tensioning. Stack height and strap spacing are confirmed per project.
Apa yang dilakukan mesin itu
The machine is a gantry cross strapping machine for aluminum ingot stacks. The stack is positioned on the carrier under the frame, and a strapping head lowers onto the top of the stack and applies the cross straps.
The strapped stack stays on the carrier for the next stage. Stack size and strap pattern are confirmed per project.
Gantry frame and strapping head
A steel gantry frame carries a crossbeam above the work area, and the strapping head hangs below the beam with its supply and drive units. The head lowers and lifts on a vertical slide, and a control box on the frame carries the electrical connections.
The head fits around the stack so the strap is guided across the block. Strap width and stack width are confirmed per project.
Strapping cycle and control
The cycle starts with a stack on the carrier under the frame. The strapping head lowers onto the stack, the strap is applied across the block, and the head lifts clear when the pass is done.
A cabinet beside the frame houses the controls, and the head returns to its raised position between stacks. Cycle time and strap tension are confirmed per project.
Apa yang ditunjukkan oleh rekaman tersebut
Our footage shows an aluminum ingot stack standing on a carrier under a gantry frame, with a strapping head held above the stack. The crossbeam lowers the head onto the top of the stack and lifts it clear again, and a second ingot stack waits off to the side. It is a general demonstration, so your stack size, strap type and cycle time are confirmed with us per project.
Konfigurasi khas
Angka-angka di bawah ini mencantumkan batasan desain fungsional, bukan nilai numerik, dan dikonfirmasi per proyek.
| Parameter | Kisaran tipikal, dikonfirmasi per proyek. |
|---|---|
| Beban | aluminum ingot stacks on the carrier under the gantry |
| Bingkai | steel gantry columns and crossbeam |
| Kepala yang gagah | head lowered onto the stack top, strap guided across |
| Menyediakan | strap coil and drive units hung below the beam |
| Sepeda | head down, strap applied, head up |
| Transfer | stack in and out on the carrier |
| kontrol | cabinet beside the frame |
| Persediaan listrik | Tegangan 380 V tiga fasa 50 Hz, atau 220 V satu fasa untuk mesin ringan, dipilih sesuai proyek. |
Daftar periksa pemilihan
| Pertanyaan | Konfirmasi per proyek |
|---|---|
| Stack range | ingot block height, width and weight |
| Tali pengikat | strap type, width and tension |
| Sepeda | strap pass time and pitch between straps |
| Pembawa | carrier width and stack positioning |
| situs | floor space for the gantry and carrier |
| Persediaan listrik | tegangan, fasa, dan frekuensi di lokasi |
Operasi dan keamanan
Position the stack on the carrier, start the cycle, and let the head lower, strap and lift automatically. Keep clear of the gantry work area and the lowering head while the machine runs.
Routine checks cover the carrier, the head and the strap supply, per the machine manual. Confirm the stack is squared on the carrier before each cycle.
Pertanyaan yang Sering Diajukan (FAQ) tentang Teknik
Q: What does this machine do? A: It straps an aluminum ingot stack by lowering a strapping head onto the top and applying the cross straps, so the block holds together.
Q: How is the strap applied? A: The head lowers over the stack and guides the strap across the block, then lifts clear when the pass is done.
Q: Does the stack move through the machine? A: The stack sits on a carrier under the frame, and the carrier and head work together through the cycle.
Q: What stacks can it handle? A: Ingot stacks of different heights and widths fit the frame, and your stack size is confirmed per project when you send your details.
T: Pasokan listrik apa yang dibutuhkan? J: Mesin ini beroperasi dengan tegangan 380 V tiga fasa 50 Hz sebagai standar, dan mesin ringan dapat diatur untuk tegangan 220 V satu fasa, yang dipilih sesuai proyek.
Langkah selanjutnya
- Email us at info@fhopepack.com with your ingot stack size and weight.
- We send a cross strapping proposal within 48 hours.
- We confirm the strap type and cycle time for your stacks.
Bacaan terkait
- Mesin Pengikat Silang Batangan Aluminium Otomatis Tingkat Lanjut
- Mesin Pelepas Tali Pengikat Kumparan
- Coil wrap packaging machine horizontal
- Lini produk mesin pengemas FHOPE
Sumber dan standar
- ISO 12100:2010 Keselamatan mesin, prinsip umum untuk desain dan penilaian risiko
- EN 415-10:2014 Keselamatan mesin pengemas, persyaratan umum
- EN ISO 13849-1:2023 Keselamatan mesin, bagian-bagian terkait keselamatan dari sistem kendali
FHOPE advanced auto aluminum ingot cross strapping machine demonstration video. Reviewed as a general demonstration; stack size, strap type and cycle time confirmed per project.
Terakhir ditinjau: 12-10-2026
