Horizontal Orbital Stretch Wrapper for Long Boards

Name: Enveloppe orbitale horizontale pour cartes
Uploaded: 2018-04-26T02:38:58+00:00
Duration: 1 min 46 s
Description: > **Executive summary** > Long boards and panels are hard to wrap by hand without gaps or loose film along their length. > Our horizontal orbital stretch wrapper in this video takes long white boards on the conveyor, lowers the wrapping arm to the product and wraps it as it…

Résumé Long boards and panels are hard to wrap by hand without gaps or loose film along their length. Our horizontal orbital stretch wrapper in this video takes long white boards on the conveyor, lowers the wrapping arm to the product and wraps it as it passes through the ring. Film per bundle follows from the tour de bague fois la périmètre du faisceau.

Table des Matières

Ce que montre la vidéo
How the boards are wrapped
Film par paquet
Commandes et sécurité
Selection checklist for a horizontal orbital wrapper for boards
FAQ technique
Suivant
Lecture connexe
Références

Ce que montre la vidéo

Long white boards come in from the left on the infeed conveyor. A unit above the conveyor comes down close to the product, and the ring turns round it, laying film on as the conveyor carries the boards through.

The wrapped boards then carry on along the outfeed conveyor and leave on the right. A control panel on the right of the machine has buttons, indicator lights and a red emergency stop. The www.fhopepack.com watermark shows in the corner of the video.

How the boards are wrapped

Les horaires sont relevés à partir des horodatages de la vidéo.

Etape	Ce qui se produit	Durée de la vidéo
Alimentation	Boards enter on the conveyor	environ 0 à 4 secondes
enveloppe	The top unit comes down and the ring wraps the boards	environ 4 à 12 secondes
Sortie	Wrapped boards carry on and leave on the right	environ 12 à 48 secondes

Wrapping happens while the boards move, so long pieces are wrapped in one pass. Wrapping time depends on the product length, ring speed and conveyor speed; the 6 m example below is arithmetic, not the board in the video.

Film par paquet

Exemple illustratif :

Produit	Valeur
Section du lot (à titre d'exemple)	300 x 100 mm
Périmètre, 2 × (1 000 + 1 200)	800 mm
Longueur du faisceau (à titre indicatif)	6 m
Avance par tour d'anneau (à titre indicatif)	125 mm
Tours de l'anneau, 5 655 ÷ 125	48
Film posé, 48 × 0.8 m	38.4 m

A smaller advance per turn means more overlap and more film for the same bundle.

Commandes et sécurité

The ring turns round the product at speed and the conveyor carries it through. Keep hands and loose clothing away from the ring while it turns, use the red emergency stop on the panel if needed, and change film only with the machine stopped and isolated.

Les normes applicables dépendent du marché de destination. Pour les marchés CE, la norme ISO 12100 définit la méthode d'évaluation des risques et la norme EN 415-10 définit les exigences générales relatives aux machines d'emballage.

Selection checklist for a horizontal orbital wrapper for boards

Bundle width, height and length range.
Finition de surface protectrice.
Type de film et chevauchement.
Infeed and outfeed conveyor lengths.
Paquets par quart de travail.
End protection or labelling.

FAQ technique

Q: What does the machine do? A: It wraps long boards in film as they pass through the turning ring.

Q: How much film does a bundle take? A: Ring turns times perimeter: 48 × 0.8 m gives 38.4 m in our example.

Q: How are the ring turns worked out? A: Bundle length over advance per turn: 6,000 ÷ 125 mm gives 48.

Q: Where is the emergency stop? A: On the control panel at the right of the machine.

Q: Can it take my board sizes? A: Send the sections and lengths and we set the ring and conveyors.

We plan your horizontal orbital stretch wrapper in three steps:

Soumettez votre plan d'aménagement avec des sections et des longueurs de faisceaux à info@fhopepack.com.
Recevez une proposition sous 48 heures, avec type de film et chevauchement.
Réservez une visite du site to check conveyor lengths and output.