Shrnutí This video shows a complete orbital wrapping cycle for a long bundle of metal profiles: it enters on a roller conveyor, a rotating arm spirals stretch film around it inside a guarded enclosure, and a fully wrapped bundle exits — all within roughly 16 seconds of footage. The machine is linear, enclosed by a safety cage, and controlled from a panel with start, stop, and emergency-stop functions.
Proč tento stroj existuje
Long, straight products — aluminum extrusions, steel tubes, pipes, plastic profiles — are awkward to protect by hand. Workers walking around a bundle with a film roll produce loose, uneven wraps, and the ends of the bundle often stay exposed. An orbitální balicí stroj do strečové fólie solves this by keeping the product stationary while a rotating ring or arm travels around it, applying stretch film in a tight, continuous spiral.
The video on this page shows exactly that process, from bare bundle to fully wrapped bundle, with no narration — only the machine at work.
Co video ukazuje: stroj v akci
The footage follows one complete cycle, stage by stage:
| Čas | Co se stane, |
|---|---|
| 0–4 | A long rectangular bundle of silver metal profiles, partially wrapped, travels on a zelený válečkový dopravník toward the white enclosed machine. |
| 4–8 | The bundle moves fully inside the machine’s enclosure. The rotating arm and film roll are visible through the wire-mesh safety cage. Film is drawn from the roll and begins to wrap. |
| 8–12 | A close-up shows the rotating arm circling the stationary bundle, stretching clear film and applying it in a spiral pattern. |
| 12–16 | The camera pulls back: the bundle exits fully encased in a tight layer of film and continues down the conveyor. |
Klíčovým bodem je, že the product does not rotate. The film ring rotates around it. This is what makes the machine practical for long profiles that would be difficult or unsafe to spin on their own axis.
Struktura stroje v kostce
From what is visible in the video:
- Main frame and enclosure: white painted steel; linear layout — product feeds in from the left, wraps in the center, exits right.
- Wrap station: enclosed by a silver metal wire-mesh safety cage with a latched door.
- Otočné rameno: holds the film dispenser; yellow and white internal components, including film guide rollers.
- Filmový systém: a large roll of clear stretch film plus a film tensioning and cutting mechanism.
- Dopravník: green roller conveyor on both sides of the wrap zone.
- Kontrolní panel: gray box on the right side near the exit, with a digitální displej, a red emergency-stop button, a green start button, a yellow button, and a black rotary knob — likely for setting adjustment, though its exact function should be confirmed with the manufacturer.
- Značení: a small white “F70V” label appears on the machine frame in the opening shot; a red and white warning label is visible near the control panel. Confirm the model designation and its meaning with the manufacturer before ordering.
Poznámky z přímého pozorování
- The video opens on a wide factory-floor shot; a long rectangular bundle of metal profiles, partially wrapped in clear plastic film, moves on a green roller conveyor toward a large white enclosed machine.
- The camera moves closer to the control panel and wrap zone; the bundle sits fully inside the enclosure, and the rotating arm and film roll are visible through the safety cage as film begins to wrap.
- A zoom shot shows the rotating arm, which holds the film dispenser, moving in a circular path around the stationary bundle; clear film is stretched and applied in a spiral pattern; a red air hose is prominent in the foreground.
- The camera pulls back to a wider view; the fully wrapped bundle exits the machine and continues along the conveyor toward the end of the line.
- Visible controls: digital display screen, red emergency-stop button, green start button, yellow button, black rotary knob.
- A watermark reading “FHOPE GROUP PACKING SOLUTION FOR YOU” and “www.fhopepack.com” is visible throughout.
Co video neukazuje
The footage demonstrates the wrapping motion, but several facts a buyer needs are not observable:
- Jmenovitá kapacita — maximum bundle weight and cross-section.
- Rozměry stroje — confirm footprint and height against your floor plan.
- doba cyklu — the video is ~16 seconds of edited footage; real cycle times depend on bundle length and wrap overlap settings.
- požadavky na napájení — voltage, phase, and amperage.
- Certifikace — CE or other safety/quality marks are not visible.
- Specifikace filmu — film gauge, width, and type are not stated.
- Detaily modelu — the “F70V” marking appears on the frame but is not explained.
Považujte vše výše uvedené za ověřte si u výrobce položek.
Kam se tento stroj hodí
Based on the product shown, this type of machine suits:
- Aluminum and steel extrusion bundles
- Pipes, tubes, and rods bundled in uniform lengths
- Any long, linear product needing dust, scratch, and moisture protection before transport or storage
To je ne the right fit for irregularly shaped, very short, or very heavy single items — the orbital design works best on long bundles with a consistent cross-section. For those cases, a turntable wrapper or a rotary-ring machine may be a better match.
Dodržené bezpečnostní prvky
- Full wire-mesh cage around the moving wrap mechanism
- Latched cage door acting as an interlock, designed to stop operation when open
- Prominent red emergency-stop button on the control panel
- Warning label on the machine frame
These are visible features only. Full interlock behavior and compliance details should be confirmed in writing before purchase.
Kontrolní seznam kupujícího
Before requesting a quotation, prepare answers to these questions:
- Co je maximum length, weight, and cross-section of your bundles?
- Co propustnost (bundles per hour) do you need?
- Co máte k dispozici napájení at the installation site?
- Potřebuješ automatic film cut and clamp, or will an operator trim the tail?
- Co film width and gauge do you currently use — and can the machine accept it?
- Kolik podlaha do you have for the machine plus infeed and outfeed conveyor?
Často kladené otázky
Otáčí se produkt během balení? No. In the video, the bundle stays stationary on the conveyor while the rotating arm circles it. This suits long profiles that should not be spun.
Jak dlouho trvá jeden balicí cyklus? The video shows a complete sequence in about 16 seconds, but it is edited footage. Actual cycle time depends on bundle length and the number of wrap passes — check with the manufacturer.
S jakými produkty zvládne? The video shows a bundle of metal profiles. Similar machines are used for pipes, hoses, and other long extruded products. Suitability for your specific product — check with the manufacturer.
Is the machine enclosed? Yes. A wire-mesh safety cage surrounds the wrap zone, with a latched door and an emergency-stop button on the control panel.
What is the “F70V” label on the frame? It is visible in the video but not explained. Verify the model designation with the manufacturer.
Související čtení
- Orbital stretch wrapper product page
- Přehled balicích strojů
- Rotační prstencový ovinovací stroj
- Stroj na balení hadic
- Automatická horizontální natahovací balička
Další krok
If you wrap long profiles, pipes, or tubes and want to replace manual wrapping with a consistent automated process, kontaktujte FHOPE with your bundle dimensions and throughput targets. Share your product samples or drawings so the right machine configuration can be confirmed before you buy.
Source and method: This article is based on the product video above. Footage was analyzed frame-by-frame using a vision model; the video contains background music only, with no narration or speech to transcribe. Specifications not visible in the video must be verified with the manufacturer.
Publikováno: 03. 09. 2026
