> **Shrnutí**
>
> A cable maker wants the brand to be the first thing a buyer sees on the coil. If the logo label is put on after wrapping it can peel off, and if it goes on before, the film hides it. Our cable coil wrapping and logo feeding machine runs a printed logo tape through the ring together with the film, so the brand is built into the wrap itself.
The wrapper sits in a working cable plant, with a touch-screen panel beside the coil station and an operator loading coils. Behind the line, finished blue and green coils are stacked with yellow labels, ready for the forklift.
Obsah
- Why feed the logo with the film
- Logo tape path and layer order
- Wrapping sequence
- Strojní data
- Wrap time and tape length
- Kontrolní seznam pro výběr
- Bezpečnost
- Často kladené otázky k inženýrství
- Další krok
- Související čtení
- Zdroje
Why feed the logo with the film
A sticker on the outside of the wrap is one more manual step and it can be torn off in handling. A logo printed on the film itself needs a full print run for each brand. Feeding a narrow printed logo tape with standard clear film gives a branded coil at the cost of a small tape roll, and the brand can be changed by changing the tape roll.
Logo tape path and layer order
The logo tape roll is mounted on the ring next to the film roll. Both run through the coil eye on every turn. Where the tape is laid decides how it looks:
- **Tape outside the film:** the logo is in full colour on the surface, but it is exposed to rubbing.
- **Tape under clear film:** the logo is protected and still readable through the film.
The layer order is set by the position of the two rolls on the ring and is chosen per customer.
Printed tape stretches less than film, so it runs on its own brake. On our cable lines the tension is held by a magnetic powder tension controller of 2.5 kg·m, which keeps the print from distorting or tearing.
Wrapping sequence
1. The coil is placed on the drive rollers.
2. The film and logo tape ends are fixed to the coil.
3. The ring turns and lays film and tape through the eye together.
4. The rollers turn the coil until the wrap closes on itself.
5. Film and tape are cut and the tails pressed down.
6. The coil is unloaded, and the next one goes on.
Strojní data
| Item | FPCA-200 | FPCA-300 |
| :--- | :--- | :--- |
| Vnitřní průměr cívky | 150–400 mm | 250–510 mm |
| Vnější průměr cívky | 250–1 200 mm | 400–1 000 mm |
| Šířka svitku | 80–200 mm | 60–300 mm |
| Hmotnost svitku | 2–1 000 kg | 20–200 kg |
| Rychlost vyzvánění | 10–120 ot./min | 10–90 ot./min |
| Wrap time | 20–30 s | 20–38 s |
| Overlap | 20–80% | 10–90% |
| Výkon | 2.0 kW | 2.4 kW |
A film-break alarm stops the cycle if the film or tape runs out, so no coil leaves half-wrapped.
Wrap time and tape length
**Wraps per coil ≈ π × OD ÷ (film width × (1 − overlap))**
**Wrap time ≈ wraps ÷ ring speed**
**Logo tape per coil ≈ wraps × 2 × (coil width + (OD − ID) ÷ 2)**
Example only: a cable coil of OD 400 mm, ID 200 mm and width 100 mm, with 60 mm film at 50% overlap, advances 30 mm per wrap. π × 400 ≈ 1,257 mm, so 1,257 ÷ 30 ≈ 42 wraps, about 21 s at 120 r/min. Each wrap is 2 × (100 + 100) = 400 mm, so a tape fed on every wrap uses about 42 × 0.4 = 16.8 m per coil.
Kontrolní seznam pro výběr
1. Coil ID, OD, width and weight.
2. Cívky za hodinu.
3. Logo tape width and roll size.
4. Tape outside or under the film.
5. Labelling or weighing after wrapping.
6. Manual loading or conveyor in-feed.
Bezpečnost
We design to EN ISO 12100:2010 for risk assessment, EN 415-10 for packaging machine safety and EN 60204-1 for the electrical equipment. The ring is guarded and an emergency stop is at the loading position.
Často kladené otázky k inženýrství
Q: Does the logo tape slow the cycle?
A: No. It is laid on the same turns as the film.
Q: Can I change the brand between orders?
A: Yes, by changing the logo tape roll.
Q: Is the logo readable under film?
A: Yes, with clear film over the tape.
Q: What if the tape runs out?
A: The film-break alarm stops the machine.
Další krok
1. **Send your coil sizes, weight, output and logo tape sample** to info@fhopepack.com.
2. **We set** the ring, film and tape layout.
3. **Odpovíme do 24 hodin** s návrhem a cenovou nabídkou.
Související čtení
- [Stroj na balicí stroj kabelových cívek FPCA-200 (produkt)](https://www.fhopepack.com/Cable-packing-machine/Cable-Coil-Wrapping-Machine-FPCA-200.html)
- [Cable coil wrapping machine FPCA-300 (product)](https://www.fhopepack.com/Cable-packing-machine/Cable-coil-wrapping-machine-FPCA-300.html)
- [Coil wrapper with logo taping](https://www.fhopepack.com/videos/coil-wrapper-with-logo-tapping/)
- [Small coil wrapping machine](https://www.fhopepack.com/videos/small-coil-wrapping-machine/)
Zdroje
- FHOPE product pages: FPCA-200, FPCA-300 cable coil wrapping machines
- FHOPE project records: logo tape wrapping and film-break alarm
- EN ISO 12100:2010; EN 415-10; EN 60204-1
Naposledy zkontrolováno: 20. 10. 2026
