Hose wrapping machine and pipe packing machine

hose wrapping machine
hose wrapping machine, pipe coil wrapping machine, garden hose packing machine


Hose wrapping machine shall wire to one side of the terminal blocks
only except where the other side is internal to the panel. EQUIPMENT SUPPLIER shall pre-wire all PLC I/O modules to terminal
blocks. EQUIPMENT SUPPLIER shall pre-wire from the incoming power
transformer to each circuit breaker and distribute to each PLC I/O module. All wire terminations shall make use of screw clamp type terminal
blocks. Wire insulation is to be stripped to sufficient length to assure a
solid connection.
Hose wrapping machine Wires are to be permanently labeled at all terminations with the wire
number. Wires shall be identified with Brady sleeve heat-shrink polyolefin
computer-printable or approved equal wire markers. Cables shall also be
identified with Electrovent Unilabel, Cat. No. ELV-688-12, or approved

Orbital stretch wrapper for furniture


Orbital stretch wrapper
Orbital stretch wrapper for wooden, panel, profile

Programmable Controller and HMI of orbital stretch wrapper PLC Make and Model
(a) The Programmable Controller (PLC) shall be manufactured by General
Electric or Siemens. The PLC shall have “Ethernet”, “Profibus”, and
“Remote I/O” capabilities. “Remote I/O“ shall be running at the highest,
reliable baud rate.


(b) The PLC System shall incorporate “Remote I/O” (“Daisy Chain”
configuration) strategically located throughout the line for ease of
installation and maintenance.
(c) The PLC Processor and any Remote I/O modules shall be supplied with a
voltage surge suppression device. Preferred manufacturers are Control
Concepts (Model IC+115), Leviton, Tycor, or equivalent.
(d) EQUIPMENT SUPPLIER shall supply DIN rail mounted circuit breakers
for the I/O modules and field I/O power.  orbital stretch wrapper HMI System
(a) HMI system is to be the latest version of GE Proficy or Siemens
(b) The package must be licensed for sufficient I/O to complete the project
plus 20% spare.

Semiauto orbital stretch wrapper and automatic spiral wrapper

Orbital stetch wrapper for wire mash
Orbital stretch wrapper for wire mash

Wiring and Terminal Blocks of the orbital stretch wrapper Terminal Blocks
(a) Terminal blocks shall be Allen Bradley, Part Number 1492-CA1 or 1492-
HM1 DIN rail mounted type.
(b) Terminal blocks shall be grouped in the panels according to voltage level.
(i.e. 120V AC, +24V D.C., analog, etc). Each group of terminals shall be
clearly identified.

All terminals of orbital stretch wrapper in panels and terminal boxes shall be indelibly marked. Thirty
five percent (35%) spare shall be added to all applications and installed at
one end of the stack.
(d) Terminal blocks marked 120V shall be used to land and distribute 120-
Volt hot, neutral, and ground wires within the wrapper panel. Terminal blocks
marked 24V shall be used to land and distribute +24 Volt and DC common
within the panel.
(e) Terminal blocks are to be labeled the same as the wire numbers
connected to them using Allen Bradley, adhesive, white labels, typed or
computer printed. Each terminal strip shall be identified with white plastic
nameplates with black lettering.

Semiauto orbital stretch wrapper video



Orbital Stretch Wrap Machine wraps your product or service directly to the pallet.As opposed to a typical stretch wrapper or stretch wrap machine that wraps product-to-merchandise, the TAB WRAPPER TORNADO secures the burden for the pallet having a protective covering of film supplying better stableness and safety for each and every delivery – even oddsized loads.

Improve packing and shipping effectiveness

Lower your material cost and labor charges

Place a stop to freight damage promisesWraps

standard, irregularly and oversizedshaped lots without any restrictions.Wraps

around a horizontal axis, in contrast to a traditional stretch-wrapper or shrink place machine that wraps about a top to bottom axis.

Item may be wrapped confidently with out removing the pallet from the forklift or through the consumption of a conveyor system.

Firmly fastens any fill to the pallet without having to use banding or strapping.

Orbital stretch wrapping machine for automatic shrink wrap


Orbital stretch wrapper
Orbital stretch wrapper for wooden, panel, profile


More information: http://www.fhopepack.com/Horizontal_wrapping_machine.html

Orbital stretch wrapping machine SUPPLIER supplied motor controls shall be housed in a standard
motor control center (MCC) enclosure, and shall provide a method for disconnecting
power from each motor circuit, and allow the operating mechanism to be locked in
the open and closed position by padlock. Refer to the Motor Control Center section
of this specification for additional information.


Orbital stretch wrapping machine SUPPLIER supplied control panel(s) shall provide a centrally
located terminal block layout, separated by voltage level, for the purpose of
terminating all field wires to and from the system. All field wires shall terminate on
one side of the terminal blocks.


Any floor mounted or large wall mounted control panel of the Orbital stretch wrapping machine shall have one 120V,
duplex convenience receptacle installed for maintenance. This does not include
outlets used for powering equipment mounted on panel. This type of panel shall also
contain a switched fluorescent strip light on the ceiling, and shall have provisions to
be “cinch” anchored to finish floor or bolted to building steel.

Orbital stretch wrapper for panel
Orbital stretch wrapper for panel