نظرة عامة
For warehouses and production lines where palletized loads must be wrapped consistently, the A200 stretch wrapping machine automates film application around the whole load and finishes it with a clean film cut. Where turntable wrappers spin the pallet, the A200 keeps the load stationary on the floor and moves the film carriage around it, which suits loads that should not be rotated. This page is written for operators and plant engineers reviewing how an A200 runs in daily use. The demonstration video below shows the machine during a wrapping and film-cutting cycle.
A200 Wrapping Machine Configuration
The A200 is built as an arm-type (gantry/rail) wrapper rather than a turntable machine. The pallet load stays on the floor while a rotating overhead arm travels around it, dispensing stretch film from a carriage mounted on the arm. For planning purposes, compare the two approaches:
| الاعداد | سلوك الحمل | الأنسب ل |
|---|---|---|
| غلاف القرص الدوار | Pallet rotates on a turntable | Light, stable loads that rotate freely |
| A200 arm-type | Pallet stays stationary, arm orbits the load | Heavier or sensitive loads, and layouts without a turntable pit |
Because nothing rotates under the load, the A200 can be placed directly at the end of a conveyor or storage aisle, and the load does not need to be stable enough to spin.
Operating the A200 Step by Step
The A200 is operated through the control panel, which offers automatic and step modes for the wrap cycle:
| خطوة | ما يحدث |
|---|---|
| 1 | Place the pallet in the wrapping zone; the load stays on the floor |
| 2 | Anchor the film tail to the load (e.g. at the base of the pallet) |
| 3 | Select automatic or step mode on the panel |
| 4 | Start the cycle; the arm orbits the load and the carriage lays film |
| 5 | At the end of the cycle, the film is cut cleanly and the pallet is removed |
Automatic mode runs the full wrap sequence without further input, which makes it the everyday choice for a steady flow of pallets. Step mode runs one move at a time and is useful when setting up a new load pattern or checking the machine. In the video the panel display is set for a customer, and the footage concentrates on the film roll and film-cutting operation. Keep clear of the wrapping zone while the arm is moving, and confirm the guarding and documentation for your market: for CE markets, FHOPE uses ISO 12100 for the risk-assessment method and EN 415-10 as the general reference for packaging-machine safety.
Film Application and Cutting
The film carriage dispenses stretch film as the arm travels around the stationary load, and the end of the cycle finishes the wrap with a film cut so the pallet leaves ready to move. Film use follows from the pallet perimeter and the load height, and the exact number of turns is controlled by the carriage program on the panel — there is no single fixed value. State the following to the manufacturer so the program and film plan are confirmed per project:
| Input to give the manufacturer | Why it decides the setup |
|---|---|
| Pallet footprint and load height | Sets the wrap count and program |
| Load type (light cartons, bags, drums) | Confirms whether a top hold or cover option is needed |
| Pallets per shift | Confirms throughput and auto-film-cut need |
| Film type and width | Matches the carriage and pre-stretch settings |
| Working language for the panel | Sets the display language of the controls |
ما يظهره اللقطات
The demonstration video is a close-up of the wrapping and film-cutting operation. Most frames show the film roll on the carriage, film being pulled from the roll and the cut finishing the wrap — the panel display appears as a secondary element. The clip does not show the full machine footprint, load dimensions or cycle times, so those must be confirmed per project with the manufacturer rather than assumed from the footage. The A200 configuration itself (load stationary, arm orbiting) follows the official A200 positioning as a stretch wrapping machine, not a turntable unit.
الأسئلة الشائعة
Is the A200 a turntable wrapper? No. The load stays on the floor while the overhead arm orbits it, so it suits loads that should not be rotated.
What do the operation modes do? Automatic mode runs the full wrap cycle; step mode runs one move at a time for setup or checking.
How is the film finished? At the end of the cycle the film is cut cleanly, so the wrapped pallet is ready to remove.
How much film does a pallet use? Film use depends on pallet perimeter, load height and the carriage program. State your pallet sizes to the manufacturer and the film plan is confirmed per project.
What should I specify? Pallet footprint and load height, pallet type, pallets per shift, film type and width, and the panel language.
الخطوة التالية
Send the manufacturer your pallet sizes, load types and pallets per shift via info@fhopepack.com; the proposal lead time depends on the scope you define. Then book a site survey to confirm floor space, power and placement.
